Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0627  Fuel Pump Control Circuit / Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0627 Fuel Pump Control Circuit / Open Even though the CPU (command area inside ECU) is outputting the suction control valve operation duty, the output monitor signal is absent for 0.5 seconds.
(1 trip detection logic)
·

Open or short in suction control valve circuit

·

Suction control valve

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0627 Fuel Press
Target Common Rail Pressure

HINT:
·

For more information on the fuel supply pump (suction control valve) and common rail system, refer to the System Description (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Press.

Under a stable operating condition such as idling, Fuel Press is within +/-5000 kPa of Target Common Rail Pressure.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0627 Idling for 1 second

WIRING DIAGRAM

A205135E01
2.063,1.396 2.26,1.573 0.198,0.177 10 2 5.427,0.698 5.698,0.875 0.271,0.177 10 41 5.427,1.375 5.698,1.552 0.271,0.177 10 81 5.708,1.281 6.125,1.458 0.417,0.177 10 PCV- 5.99,2.021 6.385,2.198 0.396,0.177 10 ECM 5.708,0.625 6.125,0.802 0.417,0.177 10 PCV+ 2.073,0.729 2.271,0.906 0.198,0.177 10 1 0.646,2.031 2.042,2.219 1.396,0.188 10 Suction Control Valve 5.99,1.833 6.26,1.99 0.271,0.156 10 B76 0.667,1.854 0.969,2.031 0.302,0.177 10 B48

CAUTION / NOTICE / HINT

NOTICE:
·
·

After replacing the fuel supply pump, the ECM needs initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.
A203056
2.25,1.094 1.521,1.563 true 1.281,1.552 1.594,1.708 0.313,0.156 10 *a 0.188,0.135 0.5,0.292 0.313,0.156 10 *1
*1 Fuel Supply Pump
*a Component without harness connected
(Suction Control Valve)


Disconnect the suction control valve connector.


b.

Measure the resistance according to the value(s) in the table below

OK:

No open or short circuit malfunction.



c.

Reconnect the suction control valve connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

NG

7.REPLACE SUCTION CONTROL VALVE
2.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-1 - B76-41 (PCV+) Always Below 1 Ω
B48-2 - B76-81 (PCV-) Always Below 1 Ω
B48-1 or B76-41 (PCV+) - Body ground Always 10 kΩ or higher
B48-2 or B76-81 (PCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Start the engine and idle it for 1 second or more.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Proceed to
DTC is not output
DTC P0627 is output




DTC is not output

END

DTC P0627 is output

4.REPLACE ECM
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and idle it for 1 second or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE SUCTION CONTROL VALVE
a.

Replace the suction control valve.

Click hereEngine / Hybrid System>2AD-FTV FUEL>SUCTION CONTROL VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

9.PERFORM SUPPLY PUMP INITIALIZATION
9.PERFORM SUPPLY PUMP INITIALIZATION

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED