Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P1626  Idle Signal Output Value Too Low  P1627  Idle Signal Output Value Too High  


DESCRIPTION

The ECM reduces injector operation speed and applied voltage to the injector to reduce the sound it produces during idling. To do this, the ECM outputs applied voltage switching signals to terminal IJEN of the injector driver (EDU) from terminal IDLO of the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1626 Idle Signal Output Value Too Low With the engine running at idle, voltage of the ECM IDLO terminal is 0.05 V or less for 5 seconds or more (1 trip detection logic).
·

Open or short in idle control circuit

·

Injector driver (EDU)

·

ECM


Comes on DTC stored
P1627 Idle Signal Output Value Too High With the engine running at speeds higher than idle, voltage of the ECM IDLO terminal is 3.4 V or higher for 5 seconds or more (1 trip detection logic).
·

Open or short in idle control circuit

·

Injector driver (EDU)

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P1626 Warm up the engine and idle it for 5 seconds
P1627

WIRING DIAGRAM

A205143
6.177,2.229 6.49,2.396 0.313,0.167 10 B76 6.177,2.385 6.531,2.552 0.354,0.167 10 ECM 5.896,1.125 6.302,1.271 0.406,0.146 10 IDLO 5.573,1.021 5.771,1.177 0.198,0.156 10 62 1.5,1.021 1.625,1.177 0.125,0.156 10 2 1.042,1.094 1.375,1.271 0.333,0.177 10 IJEN 0.5,2.448 2.458,2.677 1.958,0.229 10 Injector Driver (EDU) 0.5,2.302 0.771,2.49 0.271,0.188 10 B53

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - ECM)
a.

Disconnect the injector driver (EDU) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B53-2 (IJEN) - B76-62 (ILDO) Always Below 1 Ω
B53-2 (IJEN) or B76-62 (ILDO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE INJECTOR DRIVER (EDU)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.REPLACE INJECTOR DRIVER (EDU)
a.

Replace the injector driver (EDU).

Click hereEngine / Hybrid System>2AD-FTV FUEL>INJECTOR DRIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CHECK ANY OTHER DTCS OUTPUT
3.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Proceed to
DTC is not output
DTC P1626 or P1627 is output




DTC is not output

END

DTC P1626 or P1627 is output

4.REPLACE ECM
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

After warming up the engine, idle the engine for 5 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END