Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0069  MAP Sensor Too High or Too Low  


DESCRIPTION

To detect atmospheric pressure, the atmospheric pressure sensor built into the ECM is used in the common rail system. Following the changes in the atmospheric pressure, the ECM corrects the fuel injection volume, timing and duration, and adjusts the common rail internal fuel pressure to optimize combustion.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0069 MAP Sensor Too High or Too Low After the ignition switch is turned to ON, the difference between the atmospheric pressure sensor output and manifold absolute pressure sensor output is higher than 8 kPa for 0.5 seconds (2 trip detection logic).
·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0069
·

Atmosphere Pressure

·

MAP



HINT:
·

Turn the ignition switch to ON and check the Atmosphere Pressure and MAP items in the Data List. If the atmospheric pressure displayed on the tester differs greatly from the actual atmospheric pressure (standard: 101 kPa), the sensor (atmospheric pressure sensor or manifold absolute pressure sensor) is malfunctioning.

·

If DTC P0069 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0069 1 second elapses after ignition switch turned from off to ON (starter remains off)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


HINT:
·

Although the DTC title says MAP Sensor Too High or Too Low, this DTC relates to the atmospheric pressure sensor.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0069)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Proceed to
DTC P0069 is output
DTC P0069 and other DTCs are output


HINT:

If any DTCs other than P0069 are output, troubleshoot those DTCs first.




DTC P0069 is output

2.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR

DTC P0069 and other DTCs are output

2.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR
HINT:

Before inspecting the manifold absolute pressure sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

Powertrain > Engine > Data List
Tester Display
MAP
50003 61 314

e.

Read the value.

OK:

Same value as the actual atmospheric pressure.



Result:
Proceed to
OK
NG



OK

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTC.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Turn the ignition switch to ON for 1 second.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT