Home › Engine / Hybrid System › 2AR-FE FUEL › FUEL SYSTEM(w/o Canister Pump Module)
RM3090E _51 Engine / Hybrid System _008397 2AR-FE FUEL _0046881 FUEL SYSTEM(w/o Canister Pump Module) L

2AR-FE FUEL  FUEL SYSTEM(w/o Canister Pump Module)  PRECAUTION  


IGNITION SWITCH EXPRESSION


HINT:

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START ON (Start)



BEFORE WORKING ON FUEL SYSTEM


a.

Do not work near an open flame.


b.

Keep gasoline away from rubber and leather parts.


c.

Discharge the fuel pressure before disconnecting the fuel line to prevent gasoline from spilling out. Refer to the following procedure.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

The Discharge Fuel System Pressure procedures must be performed before disconnecting any part of the fuel system.

·

After performing the Discharge Fuel System Pressure procedures, pressure will remain in the fuel line. When disconnecting the fuel line, place a cloth or equivalent over fittings to reduce the risk of fuel spray.



a.

Remove the rear console box sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


b.
A293522

Disconnect the fuel pump and sender gauge connector.


c.

Start the engine. After the engine has stopped, turn the ignition switch off.

HINT:

If DTC P0171 (system too lean) is output, clear the DTC.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR



d.

Check that the engine does not start.


e.

Remove the fuel tank cap and discharge the pressure in the fuel tank completely.


f.

Connect the fuel pump and sender gauge connector.


g.

Install the rear console box sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>INSTALLATION



FUEL SYSTEM


a.

When disconnecting the fuel pressure fuel line, a large amount of gasoline will spill out. Follow these procedures.

i.

Disconnect the fuel pump tube.


ii.

Drain any fuel remaining inside the fuel pump tube.


iii.

To protect the disconnected fuel pump tube from damage and contamination, cover it with a plastic bag.


iv.

Put a container under the connection.



b.
A076220C04
2.156,0.771 2.229,0.417 false 2.26,1.573 2.26,1.875 false 0.594,1.375 0.594,1.708 false 1.396,0.875 1.125,0.438 1.125,0.438 1.594,0.875 false 2.917,1.323 2.917,1.531 false 2.229,0.417 2.406,0.417 false 0.948,0.323 1.146,0.521 0.198,0.198 10 *2 2.479,0.344 2.646,0.521 0.167,0.177 10 *1 2.844,1.573 3.073,1.771 0.229,0.198 10 *5 0.51,1.74 0.698,1.938 0.188,0.198 10 *3 2.177,1.917 2.385,2.115 0.208,0.198 10 *4
*1 Retainer
*2 O-Ring
*3 Nylon Tube
*4 Fuel Tube Connector
*5 Fuel Pipe


Observe these precautions when disconnecting a fuel delivery pipe (metallic type).

HINT:

The structure of a fuel tube connector is as shown in the illustration.


i.

Check if there is any damage or foreign matter on the fuel pipe connections.


ii.
A211365C01
2.399,1.481 2.597,1.651 0.198,0.17 10 *1 2.365,1.568 2.216,1.568 2.216,1.568 1.946,1.26 false
*1 No. 2 Fuel Pipe Clamp


Remove the No. 2 fuel pipe clamp.

NOTICE:

Do not reuse the No. 2 fuel pipe clamp.



iii.

Find the metallic connector of the fuel tube assembly.


iv.
A062165N01
1.979,0.719 2.49,1.635 2.49,1.635 2.021,1.854 true 2.531,1.552 2.844,1.729 0.313,0.177 10 SST

Install SST to the connector as shown in the illustration.

SST
09268-21011  


v.
A284030C05
2.594,1.604 2.177,1.385 false 0.833,1.031 1.135,1.281 1.135,1.281 1.031,0.844 true 0.542,0.854 0.5,1.26 0.5,1.26 0.75,0.583 true 1.083,1.302 1.271,1.448 0.188,0.146 10 *1 2.635,1.542 2.948,1.719 0.313,0.177 10 SST 0.396,1.292 0.583,1.438 0.188,0.146 10 *1
*1 Retainer


Turn SST, align the retainers inside the fuel tube connector with the chamfers of SST and insert SST into the connector.


vi.

Slide SST and the fuel tube connector together towards the fuel tube assembly.



c.

Observe these precautions when connecting a fuel tube connector (metallic type).

i.

Check if there is any damage or foreign matter on the fuel pipe connection.


ii.

Match the axis of the fuel tube connector with the axis of the fuel pipe, and push the fuel pipe into the fuel tube connector until the fuel tube connector makes a "click" sound. If the fuel pipe is difficult to push into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe.


iii.
A292802C02
1.906,0.844 1.885,0.875 false
V100135

Push
V100136

Pull


After connecting, check if the fuel pipe and the fuel tube connector are securely connected by pulling on them.


iv.

Install a new No. 2 fuel pipe clamp.


v.

Check that there is no fuel leakage.



d.

Observe these precautions when disconnecting the fuel tube connector (for quick type A).

i.
A211368C01
2.599,0.645 2.795,0.822 0.196,0.177 10 *1 2.548,0.736 2.416,0.736 2.416,0.736 2.026,1.145 false
*1 No. 1 Fuel Pipe Clamp


Remove the No. 1 fuel pipe clamp.


ii.

Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.


iii.
A159424C13
2.448,3.344 1.99,2.792 true 2,3.719 2.042,4.146 2.042,4.146 2.177,3.708 false 2.448,1.271 2.792,1.156 2.792,1.156 2.885,1.156 false 2.917,1.063 3.177,1.292 0.26,0.229 10 false *1 1.792,2.708 1.969,2.885 0.177,0.177 10 false *1 1.969,4.177 2.146,4.354 0.177,0.177 10 false *2
*1 Retainer
*2 O-Ring
V100135

Pinch
V100136

Pull Out


If the connector and pipe are stuck together, pinch the connector, and then push and pull the pipe to disconnect the pipe and pull it out.

NOTICE:
·

Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Check for any dirt and foreign matter on the pipe seal surface. Clean if necessary.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the main tube.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to free it. Then disconnect the main tube.




iv.

Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.


v.

To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.



e.

Observe these precautions when connecting the fuel tube connector (for quick type A)

i.

Check that there is no damage or contamination in the connecting part of the pipe.


ii.
A121423C05
1.104,1.781 1.292,1.979 0.188,0.198 10 *a 1.844,4.156 2.031,4.354 0.188,0.198 10 *b
*a Push
*b Pull


Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh engine oil to the tip of the pipe.


iii.

After connecting the pipe and the connector, check that the pipe and connector are securely connected by trying to pull them apart.


iv.

Install the No. 1 fuel pipe clamp.


v.

Inspect for fuel leaks.



f.

Observe these precautions when disconnecting the fuel tube connector (for quick type B).

i.

Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.


ii.
A293606C01
2.49,1.073 2.615,1.073 2.615,1.073 2.729,1.25 false 2.302,1 2.615,1.156 0.313,0.156 10 *1
*1 Retainer
V100135

Pull
V100136

Pull out


Pull the tabs of the fuel tube connector retainer as shown in the illustration to disconnect the fuel tube connector from the pipe.


iii.
A293524C01
1.771,1.625 1.813,1.604 false
V100135

Pull
V100136

Push


If the connector and pipe are stuck together, hold the fuel pipe by hand and push and pull on the connector. Pull the two pipes apart to separate the connector

NOTICE:
·

Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Check for any dirt and foreign matter on the pipe seal surface. Clean if necessary.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the main tube.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to free it. Then disconnect the main tube.




iv.

Check the sealing surface of the disconnected parts, and clean them if necessary.


v.

To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.



g.

Observe these precautions when connecting the fuel tube connector (for quick type B).

i.

Check that there is no damage or contamination in the connected part of the pipe.


ii.
A293526C01
2.688,1.292 2.417,1.125 2.417,1.125 2.281,1.125 false 2.094,1.042 2.406,1.198 0.313,0.156 10 *1
*1 Retainer
V100135

Insert
V100136

Push


Line up the pipe and connector and push them together until a "click" sound is heard. If the connection is tight, apply a small amount of fresh engine oil to the tip of the pipe.


iii.

Push down the retainer.


iv.
A293527C01
1.75,1.635 1.854,1.594 false
V100135

Pull


After connecting the pipe and connector, check that the pipe and connector are securely connected by trying to pull them apart.


v.

Inspect for fuel leaks.



h.

Observe these precautions when disconnecting the fuel tube connector (for quick type C).

i.
A297545C01
2.083,1.917 2.25,1.917 2.25,1.917 2.51,1.646 false 1.917,1.844 2.229,2 0.313,0.156 10 *1
*1 Retainer
V100135

Push
V100136

Pull
V100137

Pull Out


Detach the 2 claws of the connector retainer. Push down on the retainer and disconnect it from the pipe.


ii.
A297546C01
1.813,1.625 1.938,1.583 false
V100135

Pull
V100136

Push


If the connector and pipe are stuck together, pinch the fuel pipe by hand and push and pull the connector to disconnect it.

NOTICE:
·

Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Check for any dirt and foreign matter on the pipe seal surface. Clean if necessary.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the main tube.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to free it. Then disconnect the main tube.




iii.

Check for foreign matter on the seal surface of the disconnected pipe. Clean if necessary.


iv.

To protect the disconnected pipe and connector from damage and foreign matter, cover them with a plastic bag.



i.

Observe these precautions when connecting the fuel tube connector (for quick type C).

i.

Check for foreign matter on the pipe and around the connector before connecting them. Clean if necessary.


ii.
A297548C01
2.25,1.917 2.417,1.917 2.417,1.917 2.667,1.708 false 2.021,1.844 2.333,2 0.313,0.156 10 *1
*1 Retainer
V100135

Insert
V100136

Push


Align the axis of the connector with the axis of the pipe. Push the pipe into the connector, and then push up on the retainer.

NOTICE:
A297549C01
1.302,1.615 1.406,1.573 false
V100135

Pull


·

Before connecting the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

·

After connecting the pipe and connector, check that the pipe and connector are securely connected by trying to pull them apart.




iii.

Inspect for fuel leaks.




FUEL SUCTION TUBE ASSEMBLY WITH PUMP


a.
A199136

Do not disconnect the nylon tube shown in the illustration when disassembling the fuel suction tube assembly with pump. Doing so will cause reassembly of the fuel suction tube assembly with pump to be impossible as the tube is welded to the plate.