Home › Engine / Hybrid System › 2AR-FE INTAKE / EXHAUST › INTAKE SYSTEM
RM3090E _51 Engine / Hybrid System _008399 2AR-FE INTAKE / EXHAUST _0046894 INTAKE SYSTEM G

2AR-FE INTAKE / EXHAUST  INTAKE SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT INTAKE SYSTEM

HINT:

Perform "Inspection After Repair" after repairing air leaks in the intake system.



a.

Check that there are no vacuum leaks at the points shown in the illustration.

A293418C02
0.042,0.052 0.344,0.333 0.302,0.281 10 *A
*A for LHD - -


A293419C01
0.052,0.052 0.427,0.385 0.375,0.333 10 *A
*A for RHD - -



Hide 2.INSPECT INTAKE AIR CONTROL VALVE (for ACIS)

a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control.

HINT:

Perform this Active Test in less than 10 seconds.


Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Intake Control
50004 234 3

e.
A197999

When "ACIS VSV" is turned on, check that the actuator rod operates.

If the operation is not as specified, inspect the intake air control valve, vacuum tank and check valve.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE MANIFOLD>INSPECTION


f.

When "ACIS VSV" is turned off, check that the actuator rod returns to its original position.

If the operation is not as specified, inspect the intake air control valve and vacuum hose.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE MANIFOLD>INSPECTION


Hide 3.INSPECT INTAKE AIR CONTROL VALVE (for TCV)

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON (do not run the engine).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the IAC Duty Ratio / Data List / Intake Air Control Position.

HINT:

Perform this Active Test in less than 10 seconds.


Powertrain > Engine and ECT > Active Test
Tester Display
Control the IAC Duty Ratio
50004 234 150
Powertrain > Engine and ECT > Data List
Tester Display
Intake Air Control Position
50003 234 161
i.

Set the duty ratio to 60% or -60% for 1 to 3 seconds, and then return the duty ratio to 0%. Check the value in the Data List.

Specified Condition:
Condition (Active Test) Specified Condition (Data List)
IAC Duty Ratio set to 60% Intake Air Control Position 35° or more
IAC Duty Ratio set to -60% Intake Air Control Position 17° or less


NOTICE:
·

Supply power to the intake control valve for 1 to 3 seconds.

·

If power is supplied to the intake control valve for less than 1 second, the gear of the tumble control valve does not reach the stopper and the value in the Data List may be incorrect.

·

If power is supplied to the intake control valve for more than 3 seconds, the motor may be damaged.

·

Do not perform this inspection more than 2 times consecutively.



HINT:

The standard duty ratio for inspections is 60% or -60% However, if the value in the Data List is not as specified, set the duty ratio to 100% or -100% for 1 to 3 seconds and check the value in the Data List again.




e.

When the result is not as specified during the Active Test, perform the following procedures.

i.

Remove the intake manifold.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL

HINT:

When the ignition switch is off, the tumble control valves are half open.



ii.
A197127C02
1.656,4.333 1.563,4.333 1.563,4.333 1.406,4.052 false 0.948,4.333 1.063,4.333 1.063,4.333 1.188,4.052 false 0.385,4.229 0.854,4.417 0.469,0.188 10 5 (M+) 1.708,4.229 2.156,4.417 0.448,0.188 10 4 (M-) 0.75,0.25 0.917,0.448 0.167,0.198 10 *a 2.479,0.24 2.656,0.406 0.177,0.167 10 *b
*a Closed
*b Open


Check that the valves move when connecting the battery to the terminals of the intake air control valve actuator.

Standard:
Tester Connection Specified Condition
Positive (+) battery voltage applied to terminal 4 (M-), and negative (-) battery voltage applied to terminal 5 (M+) Open → Closed
Positive (+) battery voltage applied to terminal 5 (M+), and negative (-) battery voltage applied to terminal 4 (M-) Closed → Open


NOTICE:
·

Apply battery voltage for 1 to 3 seconds.

·

If battery voltage is applied for more than 3 seconds, the actuator may be damaged.

·

Do not allow the lead wires to contact the other terminals.




iii.

When the results are not as specified, perform the following inspections.

HINT:
·
A199792

Check that the valves are not cracked or deformed.

·
A199874

Remove the intake air control actuator and check that the valves move smoothly.

·

If there are no problems with the valves, inspect the intake air control valve actuator.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>INSPECTION