Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › IGNITION SYSTEM
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0046919 IGNITION SYSTEM G

2AR-FE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.PERFORM SPARK TEST

a.

Check for DTCs.


NOTICE:

If any DTC is output, perform troubleshooting procedures for that DTC.



b.

Check if sparks occur.

i.

Remove the 4 ignition coils and 4 spark plugs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL


ii.

Install the spark plug to the ignition coil and connect the ignition coil connector.


iii.
A192768

Disconnect the 4 injector connectors.


iv.

Ground the spark plug.


v.

Visually check that sparks occur while the engine is being cranked.

NOTICE:
·

When performing the inspection, be sure to ground the hexagonal portion or the threaded portion of the spark plug.

·

Do not crank the engine for more than 2 seconds.

For vehicles with a cranking hold function, turn the ignition switch off during cranking to stop cranking.

·

If an ignition coil assembly is struck or dropped, replace it with a new one.

·

If a spark plug is struck or dropped, replace it with a new one.





Hide 2.INSPECT IGNITION COIL AND SPARK TEST

a.

Spark test flowchart.

i.

Check that the wire harness side connector of the ignition coil with igniter is securely connected.

Result
Result Proceed to
NG Connect securely
OK Go to next step


ii.

Perform a spark test on a malfunctioning ignition coil with igniter.

1.

Replace the ignition coil with a normal one.

2.

Perform the spark test again.


Result
Result Proceed to
OK Replace ignition coil with igniter
NG Go to next step


iii.

Check the power supply to the ignition coil with igniter.

1.

Turn the ignition switch to ON.

2.

Check that there is battery voltage at the ignition coil positive (+) terminal.


Result
Result Proceed to
NG Check wiring between ignition switch and ignition coil with igniter
OK Go to next step


iv.

Inspect the spark plugs.

1.

If there is a cylinder in which ignition does not occur, interchange the spark plug of that cylinder and the spark plug of a cylinder in which ignition properly occurs.

2.

Check that sparks occur in the cylinder in which the properly functioning spark plug was installed.

Result:
Result Proceed to
OK Replace the spark plug
NG Inspect the ignition system
·

w/ Canister Pump Module

(Click here)

·

w/o Canister Pump Module

(Click here)





NOTICE:
·

If an ignition coil assembly is struck or dropped, replace it with a new one.

·

If a spark plug is struck or dropped, replace it with a new one.




v.

Connect the 4 injector connectors.


vi.

Install the 4 ignition coils and 4 spark plugs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION




Hide 19100P 3.CHECK SPARK PLUG

a.
I039522C07
1.083,1.979 0.906,2.063 0.906,2.063 0.646,2.063 false 0.479,1.979 0.625,2.135 0.146,0.156 10 *1
*1 Body Ground


Check the electrode.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (terminal part) - Body ground Always 10 MΩ or higher


HINT:

If a megohmmeter is not available, perform the following simple inspection instead.




b.

Alternative inspection method:

i.

Start the engine.*


ii.

Increase the engine speed to 4000 rpm and then let the engine speed decrease. Perform this operation 5 times.*

NOTICE:

*: Do not perform this step if P0300 (misfire detection) or a related DTC is stored.



iii.

Remove the spark plug.


iv.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage on its threads and insulator.

If there is damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Spark Plug Type
DENSO SK16HR11



d.

Check the spark plug electrode gap.

Maximum electrode gap for used spark plug:

1.3 mm (0.0512 in.)


If the gap is more than the maximum, replace the spark plug.

Electrode gap for new spark plug:

1.0 to 1.1 mm (0.0394 to 0.0433 in.)



e.

Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner, and then dry it.

Standard air pressure:

588 kPa (6 kgf/cm2, 85 psi)


Standard duration:

20 seconds or less


HINT:

Only use a spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.