Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0051076 SFI SYSTEM(w/o Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the ignition coil assembly (No. 1 cylinder) circuit.

·

If DTC P0352 is output, check the ignition coil assembly (No. 2 cylinder) circuit.

·

If DTC P0353 is output, check the ignition coil assembly (No. 3 cylinder) circuit.

·

If DTC P0354 is output, check the ignition coil assembly (No. 4 cylinder) circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A255924E06
4.427,1.385 4.375,0.938 4.375,0.938 4.302,0.938 false 5.333,1.156 5.563,0.719 5.563,0.719 5.635,0.719 false 3.896,0.844 4.5,1 0.604,0.156 10 Igniter 4.51,0.479 5.323,0.656 0.813,0.177 10 from Battery 5.688,0.646 7.073,1.198 1.385,0.552 10 Ignition Coil Assembly (No. 1 Cylinder) 5.615,1.854 6.729,2.031 1.115,0.177 10 No. 1 Spark Plug 5.615,3.063 6.729,3.24 1.115,0.177 10 No. 2 Spark Plug 5.615,4.385 6.729,4.563 1.115,0.177 10 No. 3 Spark Plug 5.615,5.688 6.729,5.865 1.115,0.177 10 No. 4 Spark Plug 2.74,5.927 3.083,6.104 0.344,0.177 10 ECM 2.896,1.448 3.26,1.604 0.365,0.156 10 IGT1 2.885,1.75 3.26,1.896 0.375,0.146 10 IGF1 0.302,1.5 2.031,1.667 1.729,0.167 10 Crankshaft Position Sensor 0.313,3.292 2.042,3.458 1.729,0.167 10 Camshaft Position Sensor 2.885,2.76 3.25,2.917 0.365,0.156 10 IGT2 2.896,5.406 3.26,5.563 0.365,0.156 10 IGT4 2.875,4.094 3.24,4.25 0.365,0.156 10 IGT3 0.188,4.49 2.146,5.313 1.958,0.823 10 Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter Sub-assembly, Throttle Position Sensor, etc.) 3.75,3.354 6.208,3.583 2.458,0.229 10 Ignition Coil Assembly (No. 2 Cylinder) 3.74,5.958 6.531,6.188 2.792,0.229 10 Ignition Coil Assembly (No. 4 Cylinder) 3.74,4.656 6.427,4.885 2.688,0.229 10 Ignition Coil Assembly (No. 3 Cylinder)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0351 Ignition Coil "A" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM

·

No. 1 ignition coil assembly

·

ECM


Comes on DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT2 circuit between ignition coil assembly and ECM

·

No. 2 ignition coil assembly

·

ECM


Comes on DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM

·

No. 3 ignition coil assembly

·

ECM


Comes on DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT4 circuit between ignition coil assembly and ECM

·

No. 4 ignition coil assembly

·

ECM


Comes on DTC stored

Reference: Inspection using an oscilloscope.

A299080E03
0.365,1.75 0.698,1.938 0.333,0.188 10 false IGF 0.365,1.427 0.698,1.615 0.333,0.188 10 false IGT 3.021,1.521 3.354,1.708 0.333,0.188 10 false GND 3.021,2.177 3.354,2.365 0.333,0.188 10 false GND 2.76,0.771 3.354,0.979 0.594,0.208 10 false 2 V/DIV. 1.552,2.594 2.333,2.813 0.781,0.219 10 false 20 ms./DIV.


While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.

ECM Terminal Name IGT: Between IGT (1 to 4) and E1
IGF: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

A212405E23
1.802,1.677 2.198,1.854 0.396,0.177 10 ECM 2.99,1.302 3.26,1.49 0.271,0.188 10 IGT 2.979,1.729 3.26,1.885 0.281,0.156 10 IGF 4.156,1.51 4.594,1.656 0.438,0.146 10 Igniter 5.396,1.385 6.167,1.563 0.771,0.177 10 Ignition Coil 4.427,2.365 6.104,2.552 1.677,0.188 10 Ignition Coil Assembly 0.24,3.115 1.177,3.448 0.938,0.333 10 Ignition Signal (IGT) 1.677,3.573 2.167,3.76 0.49,0.188 10 Normal 1.417,3.969 2.188,4.156 0.771,0.188 10 Malfunction 0.052,3.875 1.365,4.344 1.313,0.469 10 Ignition Confirmation Signal (IGF1) 3.604,4.51 4.458,4.688 0.854,0.177 10 Circuit Open 5.948,4.969 6.313,5.167 0.365,0.198 10 Time

If the ECM does not receive any IGF1 signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Start the engine and run it at idle for 10 seconds or more.


WIRING DIAGRAM

A298877
3.573,1.656 5.51,1.896 1.938,0.24 10 false No. 1 Ignition Coil Assembly 3.573,3.26 5.51,3.5 1.938,0.24 10 false No. 2 Ignition Coil Assembly 3.583,4.865 5.521,5.104 1.938,0.24 10 false No. 3 Ignition Coil Assembly 1.021,4.427 2.854,4.635 1.833,0.208 10 false Ignition Switch Assembly*2 3.573,1.479 4.01,1.677 0.438,0.198 10 false B12 3.583,3.083 4.021,3.281 0.438,0.198 10 false B11 3.594,4.688 4.031,4.885 0.438,0.198 10 false B10 3.573,6.219 4.01,6.417 0.438,0.198 10 false B9 3.958,0.76 4.396,0.958 0.438,0.198 10 false +B 3.938,2.365 4.375,2.563 0.438,0.198 10 false +B 3.948,3.958 4.385,4.156 0.438,0.198 10 false +B 3.948,5.479 4.385,5.677 0.438,0.198 10 false +B 3.938,1.073 4.375,1.271 0.438,0.198 10 false GND 3.948,2.698 4.385,2.896 0.438,0.198 10 false GND 3.948,4.271 4.385,4.469 0.438,0.198 10 false GND 3.948,5.896 4.385,6.094 0.438,0.198 10 false GND 4.542,0.74 4.979,0.938 0.438,0.198 10 false IGT1 4.531,2.365 4.969,2.563 0.438,0.198 10 false IGT2 4.552,3.958 4.99,4.156 0.438,0.198 10 false IGT3 4.552,5.49 4.99,5.688 0.438,0.198 10 false IGT4 4.604,1.083 5.042,1.281 0.438,0.198 10 false IGF 4.615,2.677 5.052,2.875 0.438,0.198 10 false IGF 4.604,4.26 5.042,4.458 0.438,0.198 10 false IGF 4.615,5.875 5.052,6.073 0.438,0.198 10 false IGF 5.875,0.594 6.313,0.792 0.438,0.198 10 false IGT1 5.875,2.198 6.313,2.396 0.438,0.198 10 false IGT2 5.885,3.781 6.323,3.979 0.438,0.198 10 false IGT3 5.885,5.313 6.323,5.51 0.438,0.198 10 false IGT4 5.885,5.792 6.323,5.99 0.438,0.198 10 false IGF1 6.094,6.26 6.531,6.458 0.438,0.198 10 false B77 6.094,6.438 6.531,6.635 0.438,0.198 10 false ECM 5.625,5.75 5.969,5.958 0.344,0.208 10 false 51 5.625,5.354 6.063,5.552 0.438,0.198 10 false 54 5.635,2.25 6.073,2.448 0.438,0.198 10 false 56 5.635,3.833 6.073,4.031 0.438,0.198 10 false 55 5.635,0.625 6.073,0.823 0.438,0.198 10 false 57 4.979,0.635 5.417,0.833 0.438,0.198 10 false 3 4.99,3.833 5.396,4.042 0.406,0.208 10 false 3 4.99,2.25 5.427,2.448 0.438,0.198 10 false 3 5,5.76 5.438,5.958 0.438,0.198 10 false 2 4.99,5.365 5.427,5.563 0.438,0.198 10 false 3 4.99,4.156 5.427,4.354 0.438,0.198 10 false 2 4.99,2.563 5.427,2.76 0.438,0.198 10 false 2 4.979,0.938 5.417,1.135 0.438,0.198 10 false 2 3.708,0.635 4.146,0.833 0.438,0.198 10 false 1 3.719,2.24 4.156,2.438 0.438,0.198 10 false 1 3.729,3.844 4.167,4.042 0.438,0.198 10 false 1 3.729,5.354 4.167,5.552 0.438,0.198 10 false 1 3.729,5.76 4.167,5.958 0.438,0.198 10 false 4 3.729,4.156 4.167,4.354 0.438,0.198 10 false 4 3.729,2.563 4.167,2.76 0.438,0.198 10 false 4 3.708,0.948 4.146,1.146 0.438,0.198 10 false 4 1.135,2.99 2.771,3.448 1.635,0.458 10 false Certification ECU (Smart Key ECU Assembly)*1 1.135,2.813 1.573,3.01 0.438,0.198 10 false G82 1.021,4.25 1.458,4.448 0.438,0.198 10 false G4 0.635,0.917 1.073,1.115 0.438,0.198 10 false IG2 1.698,1.604 2.135,1.802 0.438,0.198 10 false IG2 2.229,0.635 2.667,0.833 0.438,0.198 10 false 5 2.219,1.146 2.656,1.344 0.438,0.198 10 false 1 1.365,1.146 1.802,1.344 0.438,0.198 10 false 2 1.365,0.625 1.802,0.823 0.438,0.198 10 false 3 2.021,3.771 2.458,3.969 0.438,0.198 10 false IG2 2.344,3.771 2.781,3.969 0.438,0.198 10 false 3 1.354,3.771 1.792,3.969 0.438,0.198 10 false AM2 1.167,3.76 1.604,3.958 0.438,0.198 10 false 4 0.604,4.063 1.042,4.26 0.438,0.198 10 false AM2 1.854,2.292 2.292,2.49 0.438,0.198 10 false IG2D 2.292,2.167 2.729,2.365 0.438,0.198 10 false 9 0.938,5.99 2.906,6.198 1.969,0.208 10 false *1: w/ Entry and Start System 0.927,6.313 2.896,6.521 1.969,0.208 10 false *2: w/o Entry and Start System 0.531,5.531 1.281,5.729 0.75,0.198 10 false Battery 3.573,6.385 5.51,6.625 1.938,0.24 10 false No. 4 Ignition Coil Assembly 2.646,2.198 3.083,2.396 0.438,0.198 10 false *1 0.958,3.802 1.396,4 0.438,0.198 10 false *2 2.667,3.802 3.104,4 0.438,0.198 10 false *2 0.375,4.781 0.969,4.958 0.594,0.177 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B12-4 (GND) - Body ground Always Below 1 Ω
B11-4 (GND) - Body ground Always Below 1 Ω
B10-4 (GND) - Body ground Always Below 1 Ω
B9-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.
A194110
0.333,1.083 0.75,1.417 0.417,0.333 0.333,1.5 0.75,1.833 0.417,0.333 0.333,1.917 0.75,2.25 0.417,0.333 0.333,2.333 0.75,2.667 0.417,0.333 1.302,2.51 0.781,3.042 false 2.156,2.51 2.625,3.031 false 0.146,0.125 0.333,0.333 0.188,0.208 10 *a 0.646,3.063 0.854,3.24 0.208,0.177 10 +B 2.604,3.052 2.969,3.208 0.365,0.156 10 GND 0.417,1.583 0.698,1.771 0.281,0.188 10 B11 0.417,1.167 0.698,1.333 0.281,0.167 10 B12 0.417,2 0.698,2.188 0.281,0.188 10 B10 0.417,2.417 0.698,2.604 0.281,0.188 10 B9
*a Front view of wire harness connector
(to Ignition Coil Assembly)


Disconnect the ignition coil assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B12-1 (+B) - B12-4 (GND) Ignition switch ON 11 to 14 V
B11-1 (+B) - B11-4 (GND) Ignition switch ON 11 to 14 V
B10-1 (+B) - B10-4 (GND) Ignition switch ON 11 to 14 V
B9-1 (+B) - B9-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (IG2 RELAY - IGNITION COIL ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B12-2 (IGF) - B77-51 (IGF1) Always Below 1 Ω
B11-2 (IGF) - B77-51 (IGF1) Always Below 1 Ω
B10-2 (IGF) - B77-51 (IGF1) Always Below 1 Ω
B9-2 (IGF) - B77-51 (IGF1) Always Below 1 Ω
B12-3 (IGT1) - B77-57 (IGT1) Always Below 1 Ω
B11-3 (IGT2) - B77-56 (IGT2) Always Below 1 Ω
B10-3 (IGT3) - B77-55 (IGT3) Always Below 1 Ω
B9-3 (IGT4) - B77-54 (IGT4) Always Below 1 Ω
B12-3 (IGT1) or B77-57 (IGT1) - Body ground Always 10 kΩ or higher
B11-3 (IGT2) or B77-56 (IGT2) - Body ground Always 10 kΩ or higher
B10-3 (IGT3) or B77-55 (IGT3) - Body ground Always 10 kΩ or higher
B9-3 (IGT4) or B77-54 (IGT4) - Body ground Always 10 kΩ or higher
B12-2 (IGF), B11-2 (IGF), B10-2 (IGF), B9-2 (IGF) or B77-51 (IGF1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

NOTICE:

Do not change the location of the connectors.



f.

Perform a simulation test.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
Same DTC output A
Different ignition coil DTC output B


HINT:

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION




A

B

5.CHECK HARNESS AND CONNECTOR (IG2 RELAY - IGNITION COIL ASSEMBLY)
a.

Disconnect the ignition coil assembly connectors.


b.

Remove the IG2 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B12-1 (+B) - IG2 relay terminal 5 Always Below 1 Ω
B11-1 (+B) - IG2 relay terminal 5 Always Below 1 Ω
B10-1 (+B) - IG2 relay terminal 5 Always Below 1 Ω
B9-1 (+B) - IG2 relay terminal 5 Always Below 1 Ω
B12-1 (+B), B11-1 (+B), B10-1 (+B), B9-1 (+B) or IG2 relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR