Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008405 3ZR-FE ENGINE MECHANICAL _0046945 CYLINDER HEAD GASKET A

3ZR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 11115 1.INSTALL CYLINDER HEAD GASKET

a.
A215254C09
1.198,0.583 1.813,0.323 1.813,0.323 1.948,0.323 false 0.917,0.469 1.229,0.271 1.229,0.271 1.313,0.271 false 1.979,0.25 2.292,0.406 0.313,0.156 10 *1 1.344,0.188 1.656,0.344 0.313,0.156 10 *2 1,0 1.313,0.156 0.313,0.156 10 *a 1.25,1.208 1.563,1.365 0.313,0.156 10 *b 0.219,0.406 0.531,0.563 0.313,0.156 10 *3 1.25,2.531 1.563,2.688 0.313,0.156 10 *b
*1 Cylinder Block
*2 Seal Packing
*3 Seal Packing Diameter
*a Distance from Edge of Cylinder Block to Center of Seal Packing
*b Seal Packing Application Length
V100135

Engine Front


Apply seal packing to the cylinder block as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal packing diameter:

4.0 mm (0.157 in.)


Application Specification:
Distance from Edge of Cylinder Block to Center of Seal Packing Seal Packing Application Length
2.0 to 4.0 mm (0.0787 to 0.157 in.) 10 to 15 mm (0.394 to 0.591 in.)


NOTICE:

Remove any oil from the cylinder block.



b.
A221760C07
1.427,0.5 1.646,0.25 1.646,0.25 1.792,0.25 true 1.823,0.167 2.135,0.323 0.313,0.156 10 *1
*1 Lot No.
V100135

Engine Front


Place a new cylinder head gasket on the cylinder block with the Lot No. stamp facing upward.

NOTICE:

Install the cylinder head gasket within 3 minutes after applying seal packing.



c.
A233569C05
1.969,0.406 1.833,0.406 1.833,0.406 1.344,0.615 false 1.104,0.5 1.417,0.302 1.417,0.302 1.49,0.302 false 2.01,0.344 2.323,0.5 0.313,0.156 10 *1 1.531,0.219 1.844,0.375 0.313,0.156 10 *2 1.229,0.01 1.542,0.167 0.313,0.156 10 *a 1.333,2.521 1.646,2.677 0.313,0.156 10 *b 0.458,0.438 0.771,0.594 0.313,0.156 10 *3 1.333,1 1.646,1.156 0.313,0.156 10 *b
*1 Cylinder Head Gasket
*2 Seal Packing
*3 Seal Packing Diameter
*a Distance from Edge of Cylinder Head Gasket to Center of Seal Packing
*b Seal Packing Application Length
V100135

Engine Front


Apply seal packing to the cylinder head gasket as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal packing diameter:

4.0 mm (0.157 in.)


Application Specification:
Distance from Edge of Cylinder Head Gasket to Center of Seal Packing Seal Packing Application Length
0 to 2.0 mm (0 to 0.0787 in.) 10 to 15 mm (0.394 to 0.591 in.)


NOTICE:
·

Remove any oil from the cylinder head gasket and cylinder head sub-assembly.

·

Install the cylinder head sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.




Hide 11101 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
·

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION

·

The cylinder head bolts are tightened in 3 progressive steps.



a.

Place the cylinder head sub-assembly on the cylinder block.

NOTICE:
·

Make sure that no oil is on the mounting surface of the cylinder head sub-assembly.

·

Place the cylinder head sub-assembly on the cylinder block gently in order not to damage the gasket with the bottom part of the head.




b.

Install the plate washers to the cylinder head bolts.


c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


d.
A150891E02
0.583,0.099 0.691,0.25 0.108,0.152 10 8 1.122,0.099 1.229,0.25 0.108,0.152 10 4 1.668,0.113 1.775,0.264 0.108,0.152 10 2 2.2,0.113 2.308,0.264 0.108,0.152 10 5 2.768,0.092 2.875,0.244 0.108,0.152 10 9 1.647,1.78 1.761,1.935 0.114,0.155 10 1 1.095,1.782 1.202,1.933 0.108,0.152 10 6 0.506,1.782 0.697,1.933 0.191,0.152 10 10 2.225,1.782 2.333,1.933 0.108,0.152 10 3 2.775,1.782 2.883,1.933 0.108,0.152 10 7

Step 1:

i.

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts in several steps, in the sequence shown in the illustration.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:

Do not drop the plate washers into the cylinder head sub-assembly.




e.

Step 2:

i.

Mark the front side of each cylinder head bolt head with paint.


ii.

Tighten the cylinder head bolts 90° in the sequence shown in step 1.



f.

Step 3:

i.

Tighten the cylinder head bolts another 45° in the sequence shown in step 1.


ii.

Check that the paint marks are now at a 135° angle to the front.



g.
A214976C06
0.893,2.009 1.056,2.193 0.163,0.184 10 *a 2.508,2.009 2.691,2.177 0.183,0.168 10 *b
*a Before wiping off
*b After wiping off


After tightening the cylinder head bolts, wipe off the seal packing material that has seeped out from between the contact surfaces of the cylinder head sub-assembly and cylinder block.


Hide 11103 4.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY