Home › Engine / Hybrid System › 3ZR-FE INTAKE / EXHAUST › EXHAUST MANIFOLD
RM3090E _51 Engine / Hybrid System _008408 3ZR-FE INTAKE / EXHAUST _0046966 EXHAUST MANIFOLD A

3ZR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD

a.

Install a new exhaust manifold gasket.


b.

Install the exhaust manifold with new 5 nuts.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 17118 3.INSTALL MANIFOLD STAY

A293765N01
2.417,0.49 2.573,0.688 0.156,0.198 10 1 2.563,1.26 2.719,1.458 0.156,0.198 10 1 0.156,1.344 0.313,1.542 0.156,0.198 10 2

a.

Temporarily install the manifold stay with the 3 bolts.


b.

While pushing the manifold stay toward the exhaust manifold, tighten the 2 bolts labeled 1.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


c.

Tighten the bolt labeled 2.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17410 4.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum length:

41.5 mm (1.63 in.)


If the free length is less than the minimum, replace the compression spring.


b.

Using a wire brush, remove any foreign matter from the gasket installation surface.


c.
A076194C08
2.031,1.583 1.563,1.719 1.563,1.719 1.396,1.719 true 2.438,0.979 3.042,0.979 true 1.188,1.625 1.406,1.802 0.219,0.177 10 *1 3.063,0.885 3.281,1.063 0.219,0.177 10 *2
*1 Gasket
*2 Wooden Block


Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the front exhaust pipe assembly, do not push in the gasket with the front exhaust pipe assembly.




d.

Install the front exhaust pipe assembly and 2 compression springs with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


e.

Install a new gasket to the front exhaust pipe assembly.


f.

Connect the front exhaust pipe assembly to the center exhaust pipe assembly with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17167 5.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 6.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket with the bolt.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


b.

Attach the clamp to connect the fuel hose.


Hide 89467B 7.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

Hide 11212 8.INSTALL NO. 2 CYLINDER HEAD COVER