Home › Engine / Hybrid System › 1AD-FTV FUEL › FUEL INJECTOR › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008413 1AD-FTV FUEL _0047012 FUEL INJECTOR A

1AD-FTV FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injector assemblies (including shuffling the injector assemblies between the cylinders), common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump assembly, common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the fuel inlet pipe sub-assembly with a new one.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 17705 4.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 5.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 82121 7.DISCONNECT ENGINE WIRE

a.
A271556

Remove the bolt from the wire harness bracket.


b.
A271557

Disconnect the fuel temperature sensor connector and suction control valve connector.


c.
A271558

Disconnect the engine coolant temperature sensor connector and turbocharger connector.


d.
A271560

Detach the clamp and remove the bolt and fuel hose protector.


e.
A271562

Disconnect the exhaust fuel addition injector connector.


f.
A271563

Disconnect the No. 1 vacuum switching valve connector and exhaust gas temperature sensor connector.


g.
A271564

Disconnect the 4 fuel injector connectors.


h.
A271565

Disconnect the glow plug connector.


i.

Disconnect the fuel pressure sensor connector and electric EGR control valve connector.


j.
A271566

Disconnect the diesel turbo pressure sensor connector.


k.
A271567

Disconnect the pressure discharge valve connector.


l.
A271568

Remove the 2 bolts and 5 nuts and disconnect the engine wire.


Hide 8.REMOVE INJECTION PIPE SUB-ASSEMBLY

NOTICE:

After removing the injection pipe, cover the common rail with electrical tape to prevent dirt or foreign objects from entering the pipe inlet. Also, protect the injector inlets with electrical tape or plastic bags.


a.
A271569

Remove the 2 bolts and 4 No. 2 injection pipe clamps.


b.
A271570

Using a 14 mm union nut wrench, loosen the 8 union nuts and remove the 4 injection pipe sub-assemblies.


Hide 23901E 10.REMOVE FUEL TUBE SUB-ASSEMBLY

Hide 23762 11.REMOVE NO. 2 NOZZLE LEAKAGE PIPE

a.
A271573

Slide the 3 clamps and disconnect the No. 2 fuel hose, No. 3 fuel hose and No. 4 fuel hose from the No. 2 nozzle leakage pipe.


b.
A271574C02
1.042,0.104 1.354,0.26 0.313,0.156 10 *1
*1 Check Valve


Remove the check valve and gasket.


c.

Remove the bolt and No. 2 nozzle leakage pipe.


Hide 23761A 12.REMOVE NO. 1 NOZZLE LEAKAGE PIPE

a.
A271575

Remove the 4 union bolts and 4 gaskets.


b.

Remove the bolt and No. 1 nozzle leakage pipe.


Hide 23695 13.REMOVE NO. 1 NOZZLE HOLDER CLAMP

a.
A271576

Remove the 4 nozzle holder clamp bolts, 4 washers and 4 No. 1 nozzle holder clamps.


Hide 23670 14.REMOVE INJECTOR ASSEMBLY

a.

Remove the 4 injector assemblies and 4 injection nozzle seats from the cylinder head sub-assembly.


b.

Remove the O-ring from each injector assembly.

NOTICE:

When removing the injector assembly, store the injector assemblies in the correct order so that they can be returned to their original locations when reassembling.