Home › General › INTRODUCTION › REPAIR INSTRUCTION › 2012.12–2013.11
RM3090E _V1 General _008731 INTRODUCTION _0049918 REPAIR INSTRUCTION D

INTRODUCTION  REPAIR INSTRUCTION  INITIALIZATION  


PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED


Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes) Stop and start system (Click here)
Reset back door close position
·

Power back door function

·

Back door closer function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation receiver assembly requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED


Replacement Part Necessary Procedure Link
for 1AD-FTV:

ECM


·

Learning Values Save

·

Learning Values Write


Engine start (Click here)
for 1AD-FTV:

Engine assembly


·

Crank Time Compensation Reset

·

Injector Compensation Code

·

Pilot Quantity Learning


·

Engine starting

·

DTC is output


for 1AD-FTV:

No. 1 crankshaft position sensor plate


Crank Time Compensation Reset
·

Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data

·

DTC is output


for 1AD-FTV:

Air fuel ratio sensor


A/F Sensor Compensation Reset
·

EGR volume is affected

·

DTC is output.


for 1AD-FTV
·

Supply pump assembly

·

Suction control valve


Supply Pump Initialization
·

Engine start

·

DTC is output


for 1AD-FTV:

Exhaust manifold converter sub-assembly (DPF catalyst)


Catalyst Record Clear
·

Even if catalytic converter is replaced with new one, catalyst record of DPF thermal deterioration stored in ECM is same as before replacement

·

DTC is output


for 1AD-FTV:

Injector assembly


·

Injector Compensation

·

Pilot Quantity Learning


DTC is output.
for 1AD-FTV:

ECM


Register VIN DTC P0630 is input (Click here)
for 1AD-FTV:
·

Diesel throttle body assembly

·

Electric EGR control valve assembly

·

Turbocharger sub-assembly


ECD System initialization Engine start (Click here)
for 2AD-FHV:

ECM


·

Learning Values Save

·

Learning Values Write


Engine start (Click here)
for 2AD-FHV:

Engine assembly


·

Clear Crank Time Compensation Data

·

Input Injector Compensation Code

·

Pilot Quantity Learning


·

Engine starting

·

DTC is output


for 2AD-FHV:

No. 1 crankshaft position sensor plate


Clear Crank Time Compensation Data
·

Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data

·

DTC is output


for 2AD-FHV:

Air fuel ratio sensor


A/F Sensor Compensation Reset
·

EGR volume is affected

·

DTC is output.


for 2AD-FHV:
·

Supply pump assembly

·

Suction control valve


Supply Pump Initialization
·

Engine start

·

DTC is output


for 2AD-FHV:

Exhaust manifold converter sub-assembly (DPNR catalyst)


Catalyst Record Clear
·

Even if catalytic converter is replaced with new one, catalyst record of DPNR thermal deterioration stored in ECM is same as before replacement

·

DTC is output


for 2AD-FHV:

Injector assembly


·

Input Injector Compensation Code

·

After that perform the Pilot Quantity Learning


DTC is output.
for 2AD-FHV:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AD-FHV:
·

Diesel throttle body assembly

·

Electric EGR control valve assembly


ECD System initialization Engine start (Click here)
for 2AD-FTV, CCo:

ECM


·

Learning Values Save

·

Learning Values Write


Engine start (Click here)
for 2AD-FTV, CCo:

Engine assembly


·

Clear Crank Time Compensation Data

·

Input Injector Compensation Code

·

Pilot Quantity Learning


·

Engine starting

·

DTC is output


for 2AD-FTV, CCo:

No. 1 crankshaft position sensor plate


Clear Crank Time Compensation Data
·

Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data

·

DTC is output


for 2AD-FTV, CCo:
·

Supply pump assembly

·

Suction control valve


Supply Pump Initialization
·

Engine start

·

DTC is output


for 2AD-FTV, CCo:

Injector assembly


·

Input Injector Compensation Code

·

After that perform the Pilot Quantity Learning


DTC is output.
for 2AD-FTV, CCo:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AD-FTV, CCo:
·

Diesel throttle body assembly

·

Electric EGR control valve assembly


ECD System initialization Engine start (Click here)
for 2AD-FTV, DPF:

ECM


·

Learning Values Save

·

Learning Values Write


Engine start (Click here)
for 2AD-FTV, DPF:

Engine assembly


·

Clear Crank Time Compensation Data

·

Input Injector Compensation Code

·

Pilot Quantity Learning


·

Engine starting

·

DTC is output


for 2AD-FTV, DPF:

No. 1 crankshaft position sensor plate


Clear Crank Time Compensation Data
·

Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data

·

DTC is output


for 2AD-FTV, DPF:

Air fuel ratio sensor


A/F Sensor Compensation Reset
·

EGR volume is affected

·

DTC is output.


for 2AD-FTV, DPF:
·

Supply pump assembly

·

Suction control valve


Supply Pump Initialization
·

Engine start

·

DTC is output


for 2AD-FTV, DPF:

Exhaust manifold converter sub-assembly (DPF catalyst)


Catalyst Record Clear
·

Even if catalytic converter is replaced with new one, catalyst record of DPF therminal deterioration stored in ECM is same as before replacement

·

DTC is output


for 2AD-FTV, DPF:

Injector assembly


·

Input Injector Compensation Code

·

After that perform the Pilot Quantity Learning


DTC is output.
for 2AD-FTV, DPF:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AD-FTV, DPF:
·

Diesel throttle body assembly

·

Electric EGR control valve assembly


ECD System initialization Engine start (Click here)
for 2AR-FE, w/ Canister Pump Module:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AR-FE, w/o Canister Pump Module:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AR-FE, w/ Canister Pump Module:
·

Throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Heated oxygen sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair Poor idle, engine starting, etc. (Click here)
for 2AR-FE, w/o Canister Pump Module:
·

Throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair Poor idle, engine starting, etc. (Click here)
for 3ZR-FAE:

ECM


Register VIN - (Click here)
for 3ZR-FAE:
·

Throttle body assembly

·

Cleaning the deposits from the throttle body assembly

·

Engine assembly

·

Continuously variable valve lift controller assembly

·

Cylinder head sub-assembly

·

Camshaft housing sub-assembly

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock sensor


Inspection after repair Poor idle, engine starting, etc. (Click here)
for 3ZR-FE:

ECM


Register VIN DTC P0630 is input (Click here)
for 3ZR-FE:
·

Throttle body assembly

·

Cleaning the deposits from the throttle body assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft

(for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock sensor


Inspection after repair Poor idle, engine starting, etc. (Click here)
·

Lane departure warning camera

·

Windshield glass


Adjust lane departure warning camera DTCs are output (Click here)
w/ Stop and Start System:

Engine stop and start ECU


·

Upload the number of starter operations

·

Reset air conditioning information

·

Learning of the air conditioning information

·

Clear the zero point calibration data

·

Perform zero point calibration of the deceleration sensor


Stop and start system (Click here)
w/ Stop and Start System:

Starter assembly


Clear the number of starter operations
w/ Stop and Start System:

Air conditioning amplifier assembly


·

Reset air conditioning information

·

Learning of the air conditioning information


w/ Stop and Start System:

Airbag sensor assembly


·

Clear the zero point calibration of the deceleration sensor

·

Perform zero point calibration of the deceleration sensor


for U660F:

Automatic transaxle assembly


·

Reset memory

·

Input transaxle compensation code into TCM

·

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for U660F:
·

Valve body assembly

·

Shift solenoid valve SL3 and/or SL4


·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U660F:

Shift solenoid valve SL1 and/or SL2


Perform road test to allow TCM to learn
·

Large shift shock

·

The deterioration of fuel efficiency


for U660F:

TCM (If possible, read the transaxle compensation code from the previous TCM)


Possible
·

Reset memory

·

Input Transaxle compensation code (Into the new TCM)

·

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


Impossible
·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U760E:

Automatic transaxle assembly


·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for U760E:
·

Valve body assembly

·

Shift solenoid valve SL3 and/or SL4


·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U760E:

Shift solenoid valve SL1 and/or SL2


Perform road test to allow ECM to learn
·

Large shift shock

·

The deterioration of fuel efficiency


for U760E:

ECM (If possible, read the transaxle compensation code from the previous ECM)


Possible
·

Reset memory

·

Input Transaxle compensation code (Into the new ECM)

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


Impossible
·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U760F:

Automatic transaxle assembly


·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for U760F:
·

Valve body assembly

·

Shift solenoid valve SL3 and/or SL4


·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U760F:

Shift solenoid valve SL1 and/or SL2


Perform road test to allow ECM to learn
·

Large shift shock

·

The deterioration of fuel efficiency


for U760F:

ECM (If possible, read the transaxle compensation code from the previous ECM)


Possible
·

Reset memory

·

Input Transaxle compensation code (Into the new ECM)

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


Impossible
·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for K111:
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly) (w/ VSC)

·

Deceleration sensor (w/o VSC)

·

Skid control ECU (Brake actuator assembly) (w/o VSC)


·

Reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration


·

DTC P1589 is output (Malfunction Indicator Lamp (MIL) not illuminates)

·

Deterioration of fuel efficiency


(Click here)
for K111F:
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly) (w/ VSC)

·

Deceleration sensor (w/o VSC)

·

Skid control ECU (Brake actuator assembly) (w/o VSC)


·

Reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration


·

DTC P1589 is output (Malfunction Indicator Lamp (MIL) not illuminates)

·

Deterioration of fuel efficiency


(Click here)
·

4WD ECU assembly

HINT:

When replacing the 4WD ECU assembly with a new one, it is not necessary to perform initialization.


·

Acceleration sensor (airbag sensor assembly) (w/ VSC)

·

Deceleration sensor (w/o VSC)


Clear zero point calibration data Dynamic torque control 4WD/AWD system (Click here)
·

Tire pressure warning ECU and receiver

·

Tire pressure warning valve and transmitter


·

Transmitter ID registration

·

Initialization


Tire pressure warning system for Registration:(Click here)
for Initialization:(Click here)
Skid control ECU (brake actuator assembly) Yaw rate and acceleration sensor zero point calibration. Vehicle stability control system (Click here)
Yaw rate and acceleration sensor (airbag sensor assembly)
·

Clearing zero point calibration data.

·

Yaw rate and acceleration sensor zero point calibration.

·

Acceleration sensor zero point calibration and CVT oil pressure calibration (for continuously variable transaxle).


Vehicle stability control system (Click here)
Wheel alignment adjustment
·

Clearing zero point calibration data.

·

Yaw rate and acceleration sensor zero point calibration.


Vehicle stability control system (Click here)
Power steering ECU assembly Assist map writing Power steering system (Click here)
Navigation ECU sub-assembly Calibration Parking assist monitor system (Click here)
Spiral with sensor cable sub-assembly
·

Steering angle neutral point (Initialize parking assist monitorsystem)

·

Steering angle setting


Suspension, tires, etc. Television camera assembly optical axis (Back camera position setting)
Television camera assembly
w/ Entry and Start System:
·

Certification ECU (smart key ECU assembly)

·

ID code box (immobiliser code ECU)*1

·

ECM

·

Steering lock ECU (steering lock actuator assembly)

·

Electrical key transmitter sub-assembly


Registration
·

Wireless door lock operation

·

Entry operation

·

Engine starting

·

Steering unlock


Refer to the Service Bulletin for the registration method
w/o Entry and Start System:
·

Transponder key ECU assembly

·

ECM

·

Electrical key transmitter sub-assembly


Registration Engine starting Refer to the Service Bulletin for the registration procedure.
w/o Entry and Start System:
·

Door control transmitter

·

Door control receiver


Register recognition code Wireless door lock operation (Click here)
w/ Blocking System:
·

Instrument panel integration antenna assembly

·

Telephone transceiver assembly

·

Mayday battery


Registration Engine starting Refer to the Service Bulletin for the registration procedure.
·

Occupant detection ECU

·

Front seat assembly RH (occupant classification sensor)


·

Zero point calibration

·

Sensitivity check


·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)
for Automatic Air Condition System:
·

Air conditioning amplifier assembly

·

No. 1 Air conditioning radiator damper servo sub-assembly

·

No. 2 Air conditioning radiator damper servo sub-assembly

·

No. 3 Air conditioning radiator damper servo sub-assembly

·

No. 1 Blower mode damper servo sub-assembly


Initialization servo motor Initialization servo motor (Click here)
w/ Jam Protection Function:
·

Power window regulator motor assembly

·

Power window regulator sub-assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up/down function

·

Jam protection function


(Click here)
·

Sliding roof drive gear sub-assembly (sliding roof ECU)

·

Sliding roof glass sub-assembly

·

Sliding roof drive cable sub-assembly


Initialize sliding roof ECU (pulse sensor initial position setting)
·

Automatic slide open/close and tilt up/down function of sliding roof

·

Jam protection function

·

Operation function after ignition off

·

Sliding roof open warning


(Click here)
w/ Power Back Door System:

Back door lock assembly


Initialize back door closer system Back door lock operation (Click here)
w/ Power Back Door System:

Multiplex network door ECU


Initialize power back door system Power back door system (Click here)
·

Height control sensor

·

Height leveling ECU


Height leveling ECU initialization Height leveling function (Click here)


*1: w/ Multi-information Display (Dot Display Type)