Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2012.12–2015.10
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM J

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to M, it is possible to switch the shift range between "1" (M1 range) and "6" (M6 range) using the transmission control switch.

Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" once lowers the shift range by one.

WIRING DIAGRAM

C279429E01
4.083,1.625 4.542,1.823 0.458,0.198 10 3*2 4.083,1.792 4.542,1.99 0.458,0.198 10 1*3 4.083,2.188 4.542,2.385 0.458,0.198 10 1*2 4.083,2.354 4.542,2.552 0.458,0.198 10 3*3 4.083,2.802 4.542,3 0.458,0.198 10 5 2.552,2.802 3.01,3 0.458,0.198 10 4 2.552,1.625 3.01,1.823 0.458,0.198 10 2 2.74,1.406 3.198,1.604 0.458,0.198 10 E 3.625,1.406 4.219,1.604 0.594,0.198 10 SFTU 3.635,1.99 4.229,2.188 0.594,0.198 10 SFTD 3.875,2.573 4.469,2.771 0.594,0.198 10 S 2.74,2.573 3.333,2.771 0.594,0.198 10 IG 2.458,3.177 3.052,3.375 0.594,0.198 10 G36 2.469,3.385 4.385,3.594 1.917,0.208 10 Transmission Control Switch 3.208,4.875 3.802,5.073 0.594,0.198 10 TCM 0.417,5.448 2.417,5.656 2,0.208 10 : CAN Communication Line 0.531,2.688 2.208,2.917 1.677,0.229 10 from ECU-IG NO. 1 Fuse 5.229,2.688 5.823,2.885 0.594,0.198 10 A61 5.229,2.104 5.823,2.302 0.594,0.198 10 A61 5.229,1.521 5.823,1.719 0.594,0.198 10 B76 5.281,1.302 5.875,1.5 0.594,0.198 10 61 5.281,1.885 5.875,2.083 0.594,0.198 10 28 5.323,2.479 5.917,2.677 0.594,0.198 10 9 5.604,1.521 6.198,1.719 0.594,0.198 10 SFTU 5.604,2.104 6.198,2.302 0.594,0.198 10 SFTD 5.604,2.688 6.198,2.885 0.594,0.198 10 S 5.802,5.073 6.396,5.271 0.594,0.198 10 ECM 0.75,0.313 3.323,0.729 2.573,0.417 10 to Shift Paddle Switch (Transmission Shift Switch Assembly)*1 0.292,4.438 2.219,4.635 1.927,0.198 10 *1: w/ Shift Paddle Switch 0.292,4.771 2.219,4.969 1.927,0.198 10 *2: for LHD 0.292,5.094 2.219,5.292 1.927,0.198 10 *3: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Refer to the inspection procedure for the CAN communication system.

·

If the CAN communication malfunctions, the TCM cannot receive current data from the ECM. In this case, the freeze frame data output from the TCM has not been updated, so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is an effective way to find malfunctions.

·

The malfunctioning area can be confirmed using the Bus Check function of the GTS.

for LHD:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM

for RHD:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
C267936C03
0.229,0.979 0.583,1.24 0.354,0.26 2.646,1.875 2,1.406 true 2.719,1.802 3.031,2 0.313,0.198 10 IG 0.281,1.031 0.594,1.229 0.313,0.198 10 G36 0.104,0.104 0.417,0.302 0.313,0.198 10 *a
*a Front view of wire harness connector
(to Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Switch Condition Specified Condition
G36-4 (IG) - Body ground Ignition switch ON 11 to 14 V
G36-4 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

CHECK POWER SOURCE CIRCUIT

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.

Disconnect the transmission control switch connector.


b.
C267936C04
0.229,0.979 0.583,1.24 0.354,0.26 0.875,1.885 1.5,1.406 true 0.74,1.802 1.052,2 0.313,0.198 10 E 0.281,1.031 0.594,1.229 0.313,0.198 10 G36 0.104,0.104 0.417,0.302 0.313,0.198 10 *a
*a Front view of wire harness connector
(to Transmission Control Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G36-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.

Disconnect the transmission control switch connector.


b.
C277025C06
0.802,1.802 1.219,1.385 true 1.344,1.781 1.479,1.396 true 1.771,1.792 1.76,1.385 true 2.177,1.771 2.031,1.385 true 2.635,1.771 2.292,1.396 true 1.26,1.833 1.573,2.031 0.313,0.198 10 false IG 0.74,1.823 1.052,2.021 0.313,0.198 10 false S 0.698,0.5 1.01,0.698 0.313,0.198 10 false *a 1.594,1.833 2.052,2.031 0.458,0.198 10 false SFTU 2.167,1.833 2.625,2.031 0.458,0.198 10 false E 2.531,1.833 2.99,2.031 0.458,0.198 10 false SFTD 0.104,0.104 0.479,0.344 0.375,0.24 10 false *A
*A for LHD
*a Component without harness connected
(Transmission Control Switch)


for LHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
3 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
1 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher
3 (SFTU) - 2 (E) Shift lever in M 10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever in M 10 kΩ or higher



c.
C277025C07
0.802,1.802 1.219,1.385 true 1.344,1.781 1.479,1.396 true 1.771,1.792 1.76,1.385 true 2.177,1.771 2.031,1.385 true 2.635,1.771 2.292,1.396 true 1.26,1.833 1.573,2.031 0.313,0.198 10 false IG 0.74,1.823 1.052,2.021 0.313,0.198 10 false S 0.698,0.51 1.01,0.708 0.313,0.198 10 false *a 1.594,1.833 2.052,2.031 0.458,0.198 10 false SFTD 2.167,1.833 2.625,2.031 0.458,0.198 10 false E 2.531,1.833 2.99,2.031 0.458,0.198 10 false SFTU 0.104,0.104 0.479,0.344 0.375,0.24 10 false *A
*A for RHD
*a Component without harness connected
(Transmission Control Switch)


for RHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
1 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
3 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher
1 (SFTU) - 2 (E) Shift lever in M 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever in M 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
C200874C04
1.51,2.438 1.948,2.698 0.438,0.26 1.51,0.323 1.948,0.583 0.438,0.26 2.49,1.896 2.146,1.146 true 1.74,1.927 2.146,1.01 true 2.052,4 1.708,3.25 true 1.583,2.49 1.958,2.719 0.375,0.229 10 B76 1.594,0.375 1.969,0.604 0.375,0.229 10 A61 0.135,0.104 0.417,0.302 0.281,0.198 10 *a 1.792,4.063 2.583,4.26 0.792,0.198 10 61 (SFTU) 2.219,1.99 3,2.188 0.781,0.198 10 28 (SFTD) 1.573,1.99 2.354,2.188 0.781,0.198 10 9 (S)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A61-9 (S) - Body ground
·

Ignition switch ON

·

Shift lever in M, "+" or "-"


11 to 14 V
A61-9 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in M, "+" or "-"


Below 1 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B76-61 (SFTU) - Body ground Shift lever held in "+" (Up-shift) Below 1 Ω
A61-28 (SFTD) - Body ground Shift lever held in "-" (Down-shift) Below 1 Ω
B76-61 (SFTU) - Body ground Shift lever in M 10 kΩ or higher
A61-28 (SFTD) - Body ground Shift lever in M 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR