Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The speed sensors detect the wheel speed and send the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a pulse signal and outputs it to the TCM via the combination meter. The TCM determines the vehicle speed based on the frequency of this pulse signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" When the engine coolant temperature sensor is normal and the counter gear speed is 300 rpm or more, the vehicle speed signal is not input for 2 seconds or more (1-trip detection logic).
·

Open or short in vehicle speed signal circuit

·

Combination meter system

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The TCM assumes that the vehicle is being driven when the transmission counter gear speed is more than 300 rpm and over 30 seconds have passed since the park/neutral position switch was turned off. If there is no vehicle speed signal with these conditions satisfied, the TCM concludes that there is a vehicle speed signal malfunction. The TCM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C279700E01
5.885,2.094 6.344,2.292 0.458,0.198 10 false B79 5.885,2.281 6.344,2.479 0.458,0.198 10 false TCM 3.573,1.677 5.448,1.885 1.875,0.208 10 false No. 20 Junction Connector 3.573,1.5 4.104,1.698 0.531,0.198 10 false G108 4.708,1.177 5.24,1.375 0.531,0.198 10 false 15 3.844,1.177 4.375,1.375 0.531,0.198 10 false 22 5.656,1.063 6.115,1.26 0.458,0.198 10 false SPD 0.104,0.104 1.208,0.406 1.104,0.302 12 false for LHD: 5.469,1.177 5.927,1.375 0.458,0.198 10 false 3 3.167,1.177 3.698,1.375 0.531,0.198 10 false 6 2.865,1.063 3.323,1.26 0.458,0.198 10 false +S 2.313,1.063 2.771,1.26 0.458,0.198 10 false SI 2.135,1.177 2.667,1.375 0.531,0.198 10 false 5 2.073,1.5 2.604,1.698 0.531,0.198 10 false G16 2.083,1.677 3.313,1.885 1.229,0.208 10 false Combination Meter 0.125,1.073 1.604,1.281 1.479,0.208 10 false from Skid Control ECU

C279700E02
5.885,2.094 6.344,2.292 0.458,0.198 10 B79 5.885,2.281 6.344,2.479 0.458,0.198 10 TCM 3.573,1.677 5.448,1.885 1.875,0.208 10 No. 24 Junction Connector 3.573,1.5 4.104,1.698 0.531,0.198 10 G112 4.708,1.177 5.24,1.375 0.531,0.198 10 8 3.927,1.177 4.458,1.375 0.531,0.198 10 6 5.656,1.063 6.115,1.26 0.458,0.198 10 SPD 0.104,0.104 1.208,0.406 1.104,0.302 12 for RHD: 5.469,1.177 5.927,1.375 0.458,0.198 10 3 3.167,1.177 3.698,1.375 0.531,0.198 10 6 2.865,1.063 3.323,1.26 0.458,0.198 10 +S 2.313,1.063 2.771,1.26 0.458,0.198 10 SI 2.135,1.177 2.667,1.375 0.531,0.198 10 5 2.073,1.5 2.604,1.698 0.531,0.198 10 G16 2.083,1.677 3.313,1.885 1.229,0.208 10 Combination Meter 0.125,1.073 1.604,1.281 1.479,0.208 10 from Skid Control ECU

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Data List.


e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -
Powertrain > ECT > Data List
Tester Display
Vehicle Speed
50003 64 315
OK:

Vehicle speed displayed on GTS and speedometer display are equal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK COMBINATION METER SYSTEM
2.CHECK COMBINATION METER SYSTEM
a.

Inspect the circuits that send vehicle speed signals to this system in the meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


b.

During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.


Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the B79 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - B79-3 (SPD) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - TCM)
4.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - TCM)
a.

for LHD:

Disconnect the G108 No. 20 junction connector.


b.

for RHD:

Disconnect the G112 No. 24 junction connector.


c.

Disconnect the B79 TCM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
G108-15 - B79-3 (SPD) Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
G112-8 - B79-3 (SPD) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR