Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.12–2013.11
RM3090E _58 Vehicle Interior _008784 METER / GAUGE / DISPLAY _0050254 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU).

WIRING DIAGRAM

E270443E01
5.229,3.188 7.156,3.51 1.927,0.323 10 Combination Meter Assembly 5.219,3.021 5.635,3.25 0.417,0.229 10 G16 5.594,1.99 6.01,2.219 0.417,0.229 10 +S 5.594,0.354 6.01,0.583 0.417,0.229 10 SI 5.365,0.24 5.781,0.469 0.417,0.229 10 5 5.375,1.885 5.792,2.115 0.417,0.229 10 6 0.323,1.094 3.583,1.323 3.26,0.229 10 Brake Actuator Assembly (Skid Control ECU) 2.01,0.344 2.427,0.573 0.417,0.229 10 A63 2.052,0.146 2.469,0.375 0.417,0.229 10 22 1.646,0.25 2.063,0.479 0.417,0.229 10 SP1 2.073,0.542 2.49,0.771 0.417,0.229 10 *1 0.063,7.313 0.99,7.5 0.927,0.188 10 *1: w/o VSC 0.073,7.604 1,7.792 0.927,0.188 10 *2: w/ VSC 2.375,0.344 2.792,0.573 0.417,0.229 10 A64 2.417,0.135 2.833,0.365 0.417,0.229 10 11 2.438,0.563 2.854,0.792 0.417,0.229 10 *2 0.073,7.896 1.938,8.104 1.865,0.208 10 *3: for Radio Receiver Type 0.073,8.177 1.938,8.385 1.865,0.208 10 *4: for Navigation Receiver Type 0.063,8.458 2.688,8.688 2.625,0.229 10 *5: for Radio and Display Type 0.427,2.375 2.292,2.583 1.865,0.208 10 Radio Receiver Assembly*3 2.063,2 2.479,2.229 0.417,0.229 10 G48 2.125,2.177 2.542,2.406 0.417,0.229 10 *3 2.125,1.792 2.542,2.021 0.417,0.229 10 17 1.698,3.844 2.115,4.073 0.417,0.229 10 SPD 0.427,2.667 2.885,2.875 2.458,0.208 10 Navigation ECU Sub-assembly*4 2.396,2 2.813,2.229 0.417,0.229 10 G139 2.5,2.188 2.917,2.417 0.417,0.229 10 *4 2.479,1.792 2.896,2.021 0.417,0.229 10 17 2.833,1.792 3.25,2.021 0.417,0.229 10 17 2.76,2 3.177,2.229 0.417,0.229 10 G143 2.865,2.198 3.281,2.427 0.417,0.229 10 *5 0.427,2.969 3.052,3.198 2.625,0.229 10 Radio and Display Receiver Assembly*5 0.292,4.344 2.917,4.573 2.625,0.229 10 Windshield Wiper Relay Assembly*6 2.594,7.302 3.99,7.5 1.396,0.198 10 *6: w/ Rain Sensor 0.271,4.198 0.688,4.427 0.417,0.229 10 G85 1.688,1.896 2.104,2.125 0.417,0.229 10 SPD 2.063,3.844 2.479,4.073 0.417,0.229 10 24 0.583,5.552 1,5.781 0.417,0.229 10 A67 1.594,5.167 2.198,5.406 0.604,0.24 10 SPDR 2.052,5.167 2.469,5.396 0.417,0.229 10 16 0.052,6.865 3.146,7.063 3.094,0.198 10 Certification ECU (Smart Key ECU Assembly)*8 2.615,7.594 4.646,7.99 2.031,0.396 10 *7: w/ Automatic Headlight Beam Level Control System 0.594,5.688 3.125,5.948 2.531,0.26 10 Headlight Leveling ECU Assembly*7 0.052,6.719 0.469,6.948 0.417,0.229 10 G84 1.688,6.438 2.104,6.667 0.417,0.229 10 SPD 2.052,6.438 2.469,6.667 0.417,0.229 10 27 2.646,8.156 4.729,8.385 2.083,0.229 10 *8: w/ Entry and Start System 5.938,5.563 6.563,5.76 0.625,0.198 10 B79 5.948,5.719 6.573,5.917 0.625,0.198 10 TCM*9 5.729,5.156 6.146,5.385 0.417,0.229 10 SPD 5.542,5.167 5.958,5.396 0.417,0.229 10 3 2.656,8.458 4.74,8.688 2.083,0.229 10 *9: except Manual Transaxle 6.094,6.833 6.719,7.031 0.625,0.198 10 ECM 4.667,6.542 5.292,6.74 0.625,0.198 10 A61 4.698,6.333 5.323,6.531 0.625,0.198 10 14 5.729,6.438 6.146,6.667 0.417,0.229 10 SPD 4.667,6.729 5.292,6.927 0.625,0.198 10 *10 4.865,7.281 6.656,7.531 1.792,0.25 10 *10: Engine Type Diesel 5.031,6.542 5.656,6.74 0.625,0.198 10 A62 5.073,6.333 5.698,6.531 0.625,0.198 10 57 5.042,6.74 5.667,6.938 0.625,0.198 10 *11 4.865,7.573 6.073,7.792 1.208,0.219 10 *11: 2AR-FE 4.875,7.865 6.552,8.073 1.677,0.208 10 *12: 3ZR-FE, 3ZR-FAE 5.385,6.531 6.01,6.729 0.625,0.198 10 A62 5.406,6.74 6.031,6.938 0.625,0.198 10 *12 5.438,6.333 6.063,6.531 0.625,0.198 10 44

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

When replacing the combination meter assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Proceed to
for Radio Receiver Type
for Navigation Receiver Type
for Radio and Display Type



for Radio Receiver Type

2.CHECK RADIO RECEIVER ASSEMBLY

for Navigation Receiver Type

10.CHECK NAVIGATION ECU SUB-ASSEMBLY

for Radio and Display Type

18.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
2.CHECK RADIO RECEIVER ASSEMBLY
E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G85 windshield wiper relay assembly connector.*1


c.

Disconnect the A67 headlight leveling ECU assembly connector.*2


d.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


e.

Disconnect the B79 TCM connector.*4


f.

Disconnect the A61*5 or A62*6 ECM connector.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK WINDSHIELD WIPER RELAY ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)
3.CHECK WINDSHIELD WIPER RELAY ASSEMBLY
NOTICE:

For vehicle without a rain sensor, proceed to next step.


E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Automatic Headlight Beam Level Control System

*5: w/ Entry and Start System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G139 navigation ECU sub-assembly connector.*2


d.

Disconnect the G143 radio and display receiver assembly connector.*3


e.

Disconnect the A67 headlight leveling ECU assembly connector.*4


f.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5


g.

Disconnect the B79 TCM connector.*6


h.

Disconnect the A61*7 or A62*8 ECM connector.


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HEADLIGHT LEVELING ECU ASSEMBLY

NG

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY)
4.CHECK HEADLIGHT LEVELING ECU ASSEMBLY
NOTICE:

For vehicle without an automatic headlight beam level control system, proceed to next step.


E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Entry and Start System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G139 navigation ECU sub-assembly connector.*2


d.

Disconnect the G143 radio and display receiver assembly connector.*3


e.

Disconnect the G85 windshield wiper relay assembly connector.*4


f.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5


g.

Disconnect the B79 TCM connector.*6


h.

Disconnect the A61*7 or A62*8 ECM connector.


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT LEVELING ECU)
5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
NOTICE:

For vehicle without an entry and start system, proceed to next step.


E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Automatic Headlight Beam Level Control System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G139 navigation ECU sub-assembly connector.*2


d.

Disconnect the G143 radio and display receiver assembly connector.*3


e.

Disconnect the G85 windshield wiper relay assembly connector.*4


f.

Disconnect the A67 headlight leveling ECU assembly connector.*5


g.

Disconnect the B79 TCM connector.*6


h.

Disconnect the A61*7 or A62*8 ECM connector.


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK TCM

NG

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
6.CHECK TCM
NOTICE:

For vehicle manual transaxle, proceed to next step.


E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Automatic Headlight Beam Level Control System

*6: w/ Entry and Start System

*7: Engine Type Diesel

*8: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G139 navigation ECU sub-assembly connector.*2


d.

Disconnect the G143 radio and display receiver assembly connector.*3


e.

Disconnect the G85 windshield wiper relay assembly connector.*4


f.

Disconnect the A67 headlight leveling ECU assembly connector.*5


g.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*6


h.

Disconnect the A61*7 or A62*8 ECM connector.


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK ECM

NG

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
7.CHECK ECM
E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: for Radio Receiver Type

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Automatic Headlight Beam Level Control System

*6: w/ Entry and Start System

*7: except Manual Transaxle


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.*1


c.

Disconnect the G139 navigation ECU sub-assembly connector.*2


d.

Disconnect the G143 radio and display receiver assembly connector.*3


e.

Disconnect the G85 windshield wiper relay assembly connector.*4


f.

Disconnect the A67 headlight leveling ECU assembly connector.*5


g.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*6


h.

Disconnect the B79 TCM connector.*7


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

16.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
8.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
E235636C02
0.042,0.813 0.396,1.031 0.354,0.219 0.042,1.094 0.396,1.313 0.354,0.219 2.104,0.969 2.271,0.219 2.271,0.219 2.438,0.219 false 2.021,1.198 2.51,1.938 2.51,1.938 2.677,1.938 false 0.125,0.094 0.438,0.292 0.313,0.198 10 *a 2.719,1.854 3.25,2.052 0.531,0.198 10 SP1*A 0.094,0.844 0.417,1.042 0.323,0.198 10 A63 0.104,1.125 0.417,1.323 0.313,0.198 10 A64 0.458,0.865 0.771,1.063 0.313,0.198 10 *A 0.458,1.125 0.771,1.323 0.313,0.198 10 *B 2.479,0.135 3.01,0.333 0.531,0.198 10 SP1*B
*A w/o VSC
*B w/ VSC
*a Front view of wire harness connector
(to Brake Actuator Assembly (Skid Control ECU))


*1: w/o VSC

*2: w/VSC


a.

Disconnect the A63*1 or A64*2 brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o VSC
Tester Connection Switch Condition Specified Condition
A63-22 (SP1) - Body ground Ignition switch ON 11 to 14 V

w/ VSC
Tester Connection Switch Condition Specified Condition
A64-11 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL)

NG

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
9.CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL)
E200403N05
0.177,0.969 0.573,1.188 0.396,0.219 2.708,0.365 2.531,0.365 2.531,0.365 2.219,1.094 false 2.771,0.302 2.938,0.448 0.167,0.146 10 SI 0.24,1.01 0.604,1.198 0.365,0.188 10 G16 1.333,4.094 1.458,4.24 0.125,0.146 10 A 2.969,3.521 3.302,3.667 0.333,0.146 10 GND

a.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Connect an oscilloscope to terminal G16-5 (SI) and body ground.


c.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection G16-5 (SI) - Body ground
Tool Setting 5 V/DIV., 20 ms./DIV.
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG (w/o VSC)
NG (w/ VSC)



OK

REPLACE COMBINATION METER ASSEMBLY

NG (w/o VSC)

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG (w/ VSC)

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

10.CHECK NAVIGATION ECU SUB-ASSEMBLY
E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G85 windshield wiper relay assembly connector.*1


c.

Disconnect the A67 headlight leveling ECU assembly connector.*2


d.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


e.

Disconnect the B79 TCM connector.*4


f.

Disconnect the A61*5 or A62*6 ECM connector.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK WINDSHIELD WIPER RELAY ASSEMBLY

NG

19.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION ECU SUB-ASSEMBLY)
11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)

*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G48 radio receiver assembly connector.


c.

Disconnect the G85 windshield wiper relay assembly connector.*1


d.

Disconnect the A67 headlight leveling ECU assembly connector.*2


e.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


f.

Disconnect the B79 TCM connector.*4


g.

Disconnect the A61*5 or A62*6 ECM connector.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - G48-17 (SP1) Always Below 1 Ω
G16-6 (+S) or G48-17 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY)

*1: for Radio Receiver Type

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Automatic Headlight Beam Level Control System

*5: w/ Entry and Start System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G85 windshield wiper relay assembly connector.


c.

Disconnect the G48 radio receiver assembly connector.*1


d.

Disconnect the G139 navigation ECU sub-assembly connector.*2


e.

Disconnect the G143 radio and display receiver assembly connector.*3


f.

Disconnect the A67 headlight leveling ECU assembly connector.*4


g.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5


h.

Disconnect the B79 TCM connector.*6


i.

Disconnect the A61*7 or A62*8 ECM connector.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - G85-24 (SPD) Always Below 1 Ω
G16-6 (+S) or G85-24 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT LEVELING ECU)

*1: for Radio Receiver Type

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Entry and Start System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the A67 headlight leveling ECU assembly connector.


c.

Disconnect the G48 radio receiver assembly connector.*1


d.

Disconnect the G139 navigation ECU sub-assembly connector.*2


e.

Disconnect the G143 radio and display receiver assembly connector.*3


f.

Disconnect the G85 windshield wiper relay assembly connector.*4


g.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*5


h.

Disconnect the B79 TCM connector.*6


i.

Disconnect the A61*7 or A62*8 ECM connector.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - A67-16 (SPDR) Always Below 1 Ω
G16-6 (+S) or A67-16 (SPDR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

*1: for Radio Receiver Type

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Automatic Headlight Beam Level Control System

*6: except Manual Transaxle

*7: Engine Type Diesel

*8: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the G48 radio receiver assembly connector.*1


d.

Disconnect the G139 navigation ECU sub-assembly connector.*2


e.

Disconnect the G143 radio and display receiver assembly connector.*3


f.

Disconnect the G85 windshield wiper relay assembly connector.*4


g.

Disconnect the A67 headlight leveling ECU assembly connector.*5


h.

Disconnect the B79 TCM connector.*6


i.

Disconnect the A61*7 or A62*8 ECM connector.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - A67-16 (SPDR) Always Below 1 Ω
G16-6 (+S) or A67-16 (SPDR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

*1: for Radio Receiver Type

*2: for Navigation Receiver Type

*3: for Radio and Display Type

*4: w/ Rain Sensor

*5: w/ Automatic Headlight Beam Level Control System

*6: w/ Entry and Start System

*7: Engine Type Diesel

*8: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the B79 TCM connector.


c.

Disconnect the G48 radio receiver assembly connector.*1


d.

Disconnect the G139 navigation ECU sub-assembly connector.*2


e.

Disconnect the G143 radio and display receiver assembly connector.*3


f.

Disconnect the G85 windshield wiper relay assembly connector.*4


g.

Disconnect the A67 headlight leveling ECU assembly connector.*5


h.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*6


i.

Disconnect the A61*7 or A62*8 ECM connector.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - B79-3 (SPD) Always Below 1 Ω
G16-6 (+S) or B79-3 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (U660F)
OK (U760E)
OK (U760F)
OK (K111)
OK (K111F)
NG



OK (U660F)

OK (U760E)

OK (U760F)

OK (K111)

OK (K111F)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

*1: Engine Type Diesel

*2: Engine Type Gasoline

*3: for Radio Receiver Type

*4: for Navigation Receiver Type

*5: for Radio and Display Type

*6: w/ Rain Sensor

*7: w/ Automatic Headlight Beam Level Control System

*8: w/ Entry and Start System

*9: except Manual Transaxle


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the A61*1 or A62*2 ECM connector.


c.

Disconnect the G48 radio receiver assembly connector.*3


d.

Disconnect the G139 navigation ECU sub-assembly connector.*4


e.

Disconnect the G143 radio and display receiver assembly connector.*5


f.

Disconnect the G85 windshield wiper relay assembly connector.*6


g.

Disconnect the A67 headlight leveling ECU assembly connector.*7


h.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*8


i.

Disconnect the B79 TCM connector.*9


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Engine Type Diesel
Tester Connection Condition Specified Condition
G16-6 (+S) - A61-14 (SPD) Always Below 1 Ω
G16-6 (+S) or A61-14 (SPD) - Body ground Always 10 kΩ or higher

2AR-FE
Tester Connection Condition Specified Condition
G16-6 (+S) - A62-57 (SPD) Always Below 1 Ω
G16-6 (+S) or A62-57 (SPD) - Body ground Always 10 kΩ or higher

3ZR-FE, 3ZR-FAE
Tester Connection Condition Specified Condition
G16-6 (+S) - A62-44 (SPD) Always Below 1 Ω
G16-6 (+S) or A62-44 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (1AD-FTV)
OK (2AD-FHV)
OK (2AD-FTV)
OK (2AR-FE)
OK (3ZR-FAE)
OK (3ZR-FE)
NG



OK (1AD-FTV)

OK (2AD-FHV)

OK (2AD-FTV)

OK (2AR-FE)

OK (3ZR-FAE)

OK (3ZR-FE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the A63*1 or A64*2 brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o VSC
Tester Connection Condition Specified Condition
G16-5 (SI) - A63-22 (SP1) Always Below 1 Ω
G16-5 (SI) or A63-22 (SP1) - Body ground Always 10 kΩ or higher

w/ VSC
Tester Connection Condition Specified Condition
G16-5 (SI) - A64-11 (SP1) Always Below 1 Ω
G16-5 (SI) or A64-11 (SP1) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
E179098C03
0.104,1.177 0.542,1.417 0.438,0.24 0.896,0.479 1.104,0.479 1.104,0.479 1.292,1.188 false 0.156,0.073 0.333,0.24 0.177,0.167 10 *a 0.188,1.219 0.635,1.427 0.448,0.208 10 G16 0.667,0.396 0.875,0.542 0.208,0.146 10 +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G85 windshield wiper relay assembly connector.*1


c.

Disconnect the A67 headlight leveling ECU assembly connector.*2


d.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


e.

Disconnect the B79 TCM connector.*4


f.

Disconnect the A61*5 or A62*6 ECM connector.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK WINDSHIELD WIPER RELAY ASSEMBLY

NG

20.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
19.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION ECU SUB-ASSEMBLY)

*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G139 navigation receiver assembly connector.


c.

Disconnect the G85 windshield wiper relay assembly connector.*1


d.

Disconnect the A67 headlight leveling ECU assembly connector.*2


e.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


f.

Disconnect the B79 TCM connector.*4


g.

Disconnect the A61*5 or A62*6 ECM connector.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - G139-17 (SP1) Always Below 1 Ω
G16-6 (+S) or G4139-17 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NAVIGATION ECU SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

*1: w/ Rain Sensor

*2: w/ Automatic Headlight Beam Level Control System

*3: w/ Entry and Start System

*4: except Manual Transaxle

*5: Engine Type Diesel

*6: Engine Type Gasoline


a.

Disconnect the G16 combination meter assembly connector.


b.

Disconnect the G143 radio and display receiver assembly connector.


c.

Disconnect the G85 windshield wiper relay assembly connector.*1


d.

Disconnect the A67 headlight leveling ECU assembly connector.*2


e.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.*3


f.

Disconnect the B79 TCM connector.*4


g.

Disconnect the A61*5 or A62*6 ECM connector.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-6 (+S) - G143-17 (SP1) Always Below 1 Ω
G16-6 (+S) or G4143-17 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR