Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the TCM.

If the TCM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The TCM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at more than 20 km/h (12.4 mph) for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High All conditions are met (1-trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.4 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is ON.
(d) Battery voltage (10.5 V or higher) is applied to the TCM for 20 seconds.
·

Park/neutral position switch

·

Starter relay circuit

·

Cranking holding function circuit

·

TCM


Comes on DTC stored

WIRING DIAGRAM

C279354E01
5.677,0.844 6.135,1.042 0.458,0.198 10 false NSW 5.677,1.438 6.135,1.635 0.458,0.198 10 false STA 5.677,3.229 6.135,3.427 0.458,0.198 10 false STA 5.677,4.135 6.135,4.333 0.458,0.198 10 false NSW 5.677,4.708 6.135,4.906 0.458,0.198 10 false D 5.688,5.271 6.146,5.469 0.458,0.198 10 false R 5.688,6.573 6.146,6.771 0.458,0.198 10 false E1 5.927,7.167 6.385,7.365 0.458,0.198 10 false B79 5.927,7.365 6.385,7.563 0.458,0.198 10 false TCM 5.49,6.688 5.948,6.885 0.458,0.198 10 false 8 5.417,5.375 5.875,5.573 0.458,0.198 10 false 15 5.417,4.813 5.875,5.01 0.458,0.198 10 false 16 5.417,4.25 5.875,4.448 0.458,0.198 10 false 11 5.417,3.344 5.875,3.542 0.458,0.198 10 false 10 5.323,1.438 5.781,1.635 0.458,0.198 10 false A61 5.885,1.875 6.344,2.073 0.458,0.198 10 false ECM 5.375,1.229 5.833,1.427 0.458,0.198 10 false 43 5.375,0.635 5.833,0.833 0.458,0.198 10 false 38 4.906,4.25 5.365,4.448 0.458,0.198 10 false 4 4.906,4.813 5.365,5.01 0.458,0.198 10 false 7 4.917,5.375 5.375,5.573 0.458,0.198 10 false 2 4.698,4.031 5.156,4.229 0.458,0.198 10 false B 4.625,4.594 5.083,4.792 0.458,0.198 10 false DL 4.615,5.156 5.073,5.354 0.458,0.198 10 false RL 3.906,4.875 4.365,5.073 0.458,0.198 10 false RB 3.917,4.031 4.375,4.229 0.458,0.198 10 false L 3.729,4.25 4.188,4.448 0.458,0.198 10 false 9 3.729,5.094 4.188,5.292 0.458,0.198 10 false 1 3.448,5.948 3.906,6.146 0.458,0.198 10 false B36 3.448,6.146 5.469,6.385 2.021,0.24 10 false Park/Neutral Position Switch 0.75,4.99 2.094,5.25 1.344,0.26 10 false from GAUGE Fuse 3.177,4.25 3.635,4.448 0.458,0.198 10 false 2 3.177,3.708 3.635,3.906 0.458,0.198 10 false 5 2.396,3.708 2.854,3.906 0.458,0.198 10 false 3 2.396,4.25 2.854,4.448 0.458,0.198 10 false 1 2.74,4.5 3.198,4.698 0.458,0.198 10 false ST 1.313,3.594 2.844,3.792 1.531,0.198 10 false to Starter 1.073,2.656 2.604,2.854 1.531,0.198 10 false from ST Fuse 0.073,0.844 1.917,1.292 1.844,0.448 10 false from Certification ECU (Smart Key ECU Assembly) (STAR) 0.354,1.719 2.958,1.917 2.604,0.198 10 false from Ignition Switch (ST2) 3.083,0.729 3.542,0.927 0.458,0.198 10 false *1 3.083,1.604 3.542,1.802 0.458,0.198 10 false *2 0.104,6.865 2.125,7.104 2.021,0.24 10 false *1: w/ Entry and Start System 0.104,7.292 2.125,7.531 2.021,0.24 10 false *2: w/o Entry and Start System 5.323,0.844 5.781,1.042 0.458,0.198 10 false B76

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:
·

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally. If the engine does not crank, proceed to the problem symptoms table.


·

Read freeze frame data using the GTS. The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.




PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Data List.


e.

Read the value displayed on the GTS.


f.

Crank the engine.


g.

Read the value displayed on the GTS.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Signal Starter signal/ ON or OFF
·

Engine cranking: ON

·

Engine not cranking: OFF


-
Powertrain > ECT > Data List
Tester Display
Starter Signal
50003 64 209
OK:

Starter Signal is only ON when the engine is being started (during cranking).



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712C19
1.823,0.958 2.104,0.458 true 1.281,0.948 1.052,0.469 true 1.146,1.781 1.354,1.292 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *a 2.146,0.396 2.458,0.594 0.313,0.198 10 RB 0.917,0.396 1.156,0.594 0.24,0.198 10 B 1.021,1.719 1.26,1.917 0.24,0.198 10 L
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 9 (L) Shift lever in P Below 1 Ω
4 (B) - 9 (L) Shift lever in N Below 1 Ω
4 (B) - 9 (L) Shift lever not in P 10 kΩ or higher
4 (B) - 9 (L) Shift lever not in N 10 kΩ or higher
1 (RB) - 9 (L) Shift lever in P, R, N, D or M 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)

NG

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
a.
C205632C09
1.51,0.156 1.948,0.417 0.438,0.26 1.354,1.771 1.531,1.198 true 0.063,0.073 0.375,0.271 0.313,0.198 10 *a 1.583,0.198 1.958,0.427 0.375,0.229 10 B79 1.104,1.823 1.76,2.021 0.656,0.198 10 10 (STA)
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Remove the ST relay from the No. 2 engine room relay block and junction block assembly.


c.

Disconnect the park/neutral position switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B79-10 (STA) - Body ground Ignition switch ON Below 2 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > ECT > Clear DTCs
50002 64

e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / ECT/ Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 64

g.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0617 is output B




A

END

B