Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2012.12–2015.10
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  U0100  Lost Communication with ECM / PCM "A"  


DESCRIPTION

The ECM communicates with the TCM using the Controller Area Network (CAN).

If there is a problem with this communication, the TCM stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0100 Lost Communication with ECM / PCM "A" All conditions are met for 1.25 seconds (1-trip detection logic):
·

Ignition switch is ON

·

Battery voltage is 10.5 V or higher

·

No communication between the ECM and TCM


·

Harness and connector

·

ECM

·

TCM


Comes on DTC stored

WIRING DIAGRAM

C279427E01
2.792,3.625 3.25,3.823 0.458,0.198 10 B79 2.792,3.802 3.25,4 0.458,0.198 10 TCM 3,2.635 3.521,2.865 0.521,0.229 10 CAN+ 3.031,3.177 3.552,3.406 0.521,0.229 10 CAN- 3.479,2.823 3.938,3.021 0.458,0.198 10 6 3.479,3.354 3.938,3.552 0.458,0.198 10 7 5.24,2.646 5.698,2.844 0.458,0.198 10 B76 5.24,3.188 5.698,3.385 0.458,0.198 10 B76 5.24,3.719 5.698,3.917 0.458,0.198 10 B76 5.281,2.427 5.74,2.625 0.458,0.198 10 40 5.281,2.969 5.74,3.167 0.458,0.198 10 63 5.24,3.5 5.698,3.698 0.458,0.198 10 109 5.594,3.177 6.115,3.406 0.521,0.229 10 CAN- 5.594,3.719 6.115,3.948 0.521,0.229 10 E1 5.844,4.313 6.365,4.542 0.521,0.229 10 ECM 5.594,2.635 6.115,2.865 0.521,0.229 10 CAN+ 5.594,1.583 6.188,1.813 0.594,0.229 10 MREL 5.24,1.594 5.698,1.792 0.458,0.198 10 A61 5.281,1.375 5.74,1.573 0.458,0.198 10 45 5.24,1.063 5.698,1.26 0.458,0.198 10 A61 5.594,1.052 6.188,1.281 0.594,0.229 10 +B2 5.281,0.844 5.74,1.042 0.458,0.198 10 20 5.24,0.51 5.698,0.708 0.458,0.198 10 A61 5.594,0.521 6.188,0.75 0.594,0.229 10 +B 5.323,0.302 5.781,0.5 0.458,0.198 10 1 2.448,1.938 4.479,2.219 2.031,0.281 10 EFI-MAIN NO. 1 3.313,1.156 3.771,1.354 0.458,0.198 10 3 3.313,1.688 3.771,1.885 0.458,0.198 10 1 2.521,1.156 2.979,1.354 0.458,0.198 10 5 2.521,1.688 2.979,1.885 0.458,0.198 10 2 0.115,1.052 3.781,1.25 3.667,0.198 10 from EFI-MAIN NO. 1 Fuse 0.5,4.229 4.167,4.427 3.667,0.198 10 : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:
·

Refer to the inspection procedure for the CAN communication system.

·

If the CAN communication malfunctions, the TCM cannot receive current data from the ECM. In this case, the freeze frame data output from the TCM has not been updated, so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is an effective way to find malfunctions.

·

The malfunctioning area can be confirmed using the Bus Check function of the GTS.

for LHD:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM

for RHD:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM



PROCEDURE

1.CHECK ECM TERMINAL VOLTAGE (+B AND +B2 TERMINALS)
a.
C197708C06
1.552,0.177 1.99,0.438 0.438,0.26 1.854,1.698 1.563,0.979 true 1.021,1.729 1.552,0.865 true 0.135,0.198 0.448,0.396 0.313,0.198 10 *a 1.646,0.219 2.021,0.448 0.375,0.229 10 A61 1.615,1.781 2.354,1.979 0.74,0.198 10 20 (+B2) 0.781,1.781 1.354,1.979 0.573,0.198 10 1 (+B)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A61-1 (+B) - Body ground Ignition switch ON 11 to 14 V
A61-20 (+B2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.
C197707C07
1.448,0.177 1.885,0.438 0.438,0.26 2.552,1.844 2.344,1.323 false 0.104,0.115 0.417,0.313 0.313,0.198 10 *a 1.542,0.229 1.917,0.458 0.375,0.229 10 B76 2.313,1.896 3.104,2.094 0.792,0.198 10 109 (E1)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B76-109 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - TCM)
a.

Disconnect the B76 ECM connector.


b.

Disconnect the B79 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B76-40 (CAN+) - B79-6 (CAN+) Always Below 1 Ω
B76-63 (CAN-) - B79-7 (CAN-) Always Below 1 Ω
B76-40 (CAN+) or B79-6 (CAN+) - Body ground or other terminals Always 10 kΩ or higher
B76-63 (CAN-) or B79-7 (CAN-) - Body ground or other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TCM
a.

Replace the TCM.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>TCM>REMOVAL

Result:
Proceed to
NEXT




NEXT

5.CHECK IF DTC OUTPUT RECURS (DTC U0100)
5.CHECK IF DTC OUTPUT RECURS (DTC U0100)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > ECT > Clear DTCs
50002 64

e.

Start the engine.


f.

Enter the following menus: Powertrain / ECT / Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 64

g.

Read the DTCs using the GTS.

Result:
Result Proceed to
U0100 is output A
DTCs are not output B




A

B

END