Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0791  Intermediate Shaft Speed Sensor "A" Circuit  P0793  Intermediate Shaft Speed Sensor "A"  


DESCRIPTION

This sensor detects the rotation speed of the counter gear which indicates the output speed of the transaxle. By comparing the input turbine speed (speed sensor NT) signal with the counter gear speed (speed sensor NC) signal, the TCM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0791 Intermediate Shaft Speed Sensor "A" Circuit When the speed sensor input voltage is either higher than 1.9 V or below 0.1 V for 2 seconds or more (1-trip detection logic).
·

Speed sensor NC (transmission revolution sensor)

·

Transmission wire

·

TCM


Comes on DTC stored
P0793 Intermediate Shaft Speed Sensor "A" When the vehicle speed is 25 km/h (15.5 mph) or more, the counter gear speed is less than 300 rpm for 2 seconds or more (1-trip detection logic).
·

Speed sensor NC (transmission revolution sensor)

·

Transmission wire

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The NT terminal of the TCM detects a pulse signal from speed sensor NT (input RPM). The TCM calculates gear shifts by comparing the signal from speed sensor NT with the signal from speed sensor NC.

While the vehicle is operating in 2nd, 3rd, 4th or 5th gear with the shift lever in D, if the input shaft speed is less than 300 rpm*1 although the output shaft speed is more than 1000 rpm*2, the TCM interprets this as a fault, illuminates the MIL and stores the DTC.

HINT:
·

*1: A pulse is not output or is irregularly output.

·

*2: The vehicle speed is 50 km/h (31 mph) or more.



CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NC) Counter gear speed (speed sensor NC) Min.: 0 rpm
Max.: 12750 rpm
Vehicle stopped: 0 km/h (0 mph) The data is displayed in increments of 50 rpm.
NC Sensor Voltage Counter gear speed sensor (speed sensor NC) output voltage Min.: 0 V
Max.: 5 V
Engine idling: 0.1 to 1.9 V -
Powertrain > ECT > Data List
Tester Display
SPD (NC)
NC Sensor Voltage
50003 64 158,379
HINT:
·

SPD (NC) is always 0 while driving: Open or short in the sensor or circuit.

·

SPD (NC) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.





PROCEDURE

1.INSPECT TRANSMISSION REVOLUTION SENSOR INSTALLATION
a.
C133219

Remove the transmission valve body assembly.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>REMOVAL


b.

Make sure that the connector is properly connected, and check the transmission revolution sensor installation.

OK:

The installation bolts are tightened properly and there is no clearance between the sensor and transaxle case.



Result:
Proceed to
OK
NG



OK

2.INSPECT TRANSMISSION WIRE

NG

SECURELY INSTALL OR REPLACE TRANSMISSION REVOLUTION SENSOR

2.INSPECT TRANSMISSION WIRE
a.
C206824C07
2.188,1.708 1.979,1.24 true 1.625,1.698 1.792,1.24 true 1.25,4.104 1.542,3.167 true 1.969,4.104 1.656,3.167 true 0.615,2.51 0.896,2.708 0.281,0.198 10 *b 0.51,0.427 0.729,0.625 0.219,0.198 10 *a 0.052,0.104 0.271,0.302 0.219,0.198 10 *1 1.448,1.75 1.823,1.948 0.375,0.198 10 NCO 2.073,1.75 2.427,1.948 0.354,0.198 10 NCB 1.083,4.146 1.448,4.344 0.365,0.198 10 NCB 1.844,4.146 2.229,4.344 0.385,0.198 10 NCO
*1 Transmission Wire
*a Transmission Revolution Sensor Side
*b TCM Side


Disconnect the transmission revolution sensor connector.


b.

Remove the TCM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
NCB transmission revolution sensor side - 4 (NCB) TCM side Always Below 1 Ω
NCO transmission revolution sensor side - 3 (NCO) TCM side Always Below 1 Ω
NCB transmission revolution sensor side - Body ground Always 10 kΩ or higher
NCO transmission revolution sensor side - Body ground Always 10 kΩ or higher
NCB transmission revolution sensor side - All other terminals except 4 (NCB) TCM side Always 10 kΩ or higher
NCO transmission revolution sensor side - All other terminals except 3 (NCO) TCM side Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE SPEED SENSOR NC (TRANSMISSION REVOLUTION SENSOR)

NG

3.REPLACE SPEED SENSOR NC (TRANSMISSION REVOLUTION SENSOR)
a.

Replace the transmission revolution sensor.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>SPEED SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK IF DTC OUTPUT RECURS (DTC P0791 OR P0793)
4.CHECK IF DTC OUTPUT RECURS (DTC P0791 OR P0793)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Clear the DTCs.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

HINT:

Write down the currently output DTCs before clearing them.


Powertrain > ECT > Clear DTCs
50002 64


e.

Enter the following menus: Powertrain / ECT / Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 64

f.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only P0791 or P0793 is output A
DTCs are not output B




A

B

END