Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0989  Transmission Fluid Pressure Sensor / Switch "E" Circuit Low  P0990  Transmission Fluid Pressure Sensor / Switch "E" Circuit High  


DESCRIPTION

The No. 3 ATF pressure switch is installed in the lock-up solenoid ATF output passage and is used to detect a malfunction in the lock-up solenoid.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0989 Transmission Fluid Pressure Sensor / Switch "E" Circuit Low No. 3 ATF pressure switch is off when lock-up occurs in response to a lock-up request (2-trip detection logic).
·

No. 3 ATF pressure switch (ATF temperature sensor assembly)

·

Transmission wire

·

TCM


Comes on DTC stored
P0990 Transmission Fluid Pressure Sensor / Switch "E" Circuit High Both conditions are met (2-trip detection logic):
·

No. 3 ATF pressure switch is on when lock-up does not occur.

·

Lock-up does not occur when shift solenoid valve SLU is commanded to turn off in the lock-up range.


·

No. 3 ATF pressure switch (ATF temperature sensor assembly)

·

Transmission wire

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The TCM illuminates the MIL and stores the DTC when the TCM detects that the No. 3 ATF pressure switch is off with the lock-up solenoid on or when the TCM detects that the No. 3 ATF pressure switch is on with the lock-up solenoid off.

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TPS 3 Switch No. 3 ATF pressure switch status ON or OFF
·

ON: Shift solenoid valve SLU is on

·

OFF: Shift solenoid valve SLU is off


-
Powertrain > ECT > Data List
Tester Display
TPS 3 Switch
50003 64 383


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0989 OR P0990)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 64

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only P0989 is output A
Only P0990 is output B
P0989 or P0990 and other DTCs are output C


HINT:

If a solenoid is stuck OFF, DTCs for several solenoids including the malfunctioning solenoid will be detected.




A

2.INSPECT TRANSMISSION WIRE (NO. 3 ATF PRESSURE SWITCH)

B

5.INSPECT TRANSMISSION WIRE (NO. 3 ATF PRESSURE SWITCH)

C

2.INSPECT TRANSMISSION WIRE (NO. 3 ATF PRESSURE SWITCH)
a.

Disconnect the ATF temperature sensor assembly connector.


b.

Remove the TCM.


c.
C206304C04
2.188,1.635 2.042,1.271 true 1.938,4.094 1.771,3.698 true 0.375,2.49 0.656,2.688 0.281,0.198 10 *b 0.375,0.354 0.594,0.552 0.219,0.198 10 *a 0.083,0.094 0.302,0.292 0.219,0.198 10 *1 2.042,1.677 2.469,1.875 0.427,0.198 10 TPS3 1.813,4.135 2.229,4.333 0.417,0.198 10 TPS3
*1 Transmission Wire
*a ATF Temperature Sensor Assembly Side
*b TCM Side


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
TPS3 ATF temperature sensor assembly side - 19 (TPS3) TCM side Always Below 1 Ω
TPS3 ATF temperature sensor assembly side - Body ground (transmission valve body assembly) and any other terminals except 19 (TPS3) TCM side Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 3 ATF PRESSURE SWITCH (ATF TEMPERATURE SENSOR ASSEMBLY)

NG

3.REPLACE NO. 3 ATF PRESSURE SWITCH (ATF TEMPERATURE SENSOR ASSEMBLY)
a.

Replace the ATF temperature sensor assembly.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>ATF TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK IF DTC OUTPUT RECURS (DTC P0989)
4.CHECK IF DTC OUTPUT RECURS (DTC P0989)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Clear the DTCs.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

HINT:

Write down the currently output DTCs before clearing them.


Powertrain > ECT > Clear DTCs
50002 64


e.

Enter the following menus: Powertrain / ECT / Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 64

f.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only P0989 is output A
DTCs are not output B




A

B

END

5.INSPECT TRANSMISSION WIRE (NO. 3 ATF PRESSURE SWITCH)
a.
C207057C18
1.948,1.521 1.771,1.125 true 0.604,0.229 0.917,0.427 0.313,0.198 10 *a 1.792,1.552 2.208,1.75 0.417,0.198 10 TPS3
*a Component without TCM connected
(Transmission Wire)


Remove the TCM.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
19 (TPS3) - Body ground (transmission valve body assembly) and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT NO. 3 ATF PRESSURE SWITCH (ATF TEMPERATURE SENSOR ASSEMBLY)
6.INSPECT NO. 3 ATF PRESSURE SWITCH (ATF TEMPERATURE SENSOR ASSEMBLY)
a.
C206308C06
1.198,1.427 1.375,1.063 true 0.677,0.427 0.99,0.625 0.313,0.198 10 *a 1,1.479 1.427,1.677 0.427,0.198 10 TPS3
*a Component without harness connected
(ATF Temperature Sensor Assembly)


Disconnect the ATF temperature sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
TPS3 - Body ground (transmission valve body assembly) and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 3 ATF PRESSURE SWITCH (ATF TEMPERATURE SENSOR ASSEMBLY)