Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › SHIFT LEVER
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047088 SHIFT LEVER A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL SHIFT LEVER ASSEMBLY

a.
C279460N01
0.854,1.813 1.01,2.01 0.156,0.198 10 1 2.521,0.708 2.677,0.906 0.156,0.198 10 2 0.875,0.688 1.031,0.885 0.156,0.198 10 3 2.521,1.813 2.677,2.01 0.156,0.198 10 4

Install the shift lever assembly with the 4 bolts. Tighten the bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Connect the 2 connectors and attach the 4 harness clamps to the shift lever assembly.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper to lock the nut.

C203379C02
1.563,0.552 1.438,0.167 1.438,0.167 1.354,0.167 false 1.542,1.146 1.667,1.521 1.667,1.521 1.75,1.521 false 1.198,0.094 1.365,0.271 0.167,0.177 10 *1 1.781,1.448 1.958,1.625 0.177,0.177 10 *2 3.656,0.146 3.823,0.344 0.167,0.198 10 *a
*1 Stopper *2 Nut
*a Push in - -


NOTICE:

Do not over-rotate the nut as it will come off the internal spring and the transmission control cable will not be reusable.


HINT:

If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.



b.

Connect the outer part of the transmission control cable assembly to the shift lever assembly. Check that the stopper returns to the pulled-out position.

C203380C02
1.25,0.302 1.313,0.125 1.313,0.125 1.385,0.125 true 1.177,0.885 1.063,1.229 1.063,1.229 0.99,1.229 true 1.302,1.271 1.208,1.531 1.208,1.531 1.125,1.531 true 1.417,0.063 1.594,0.24 0.177,0.177 10 *1 0.802,1.156 0.979,1.333 0.177,0.177 10 *2 0.969,1.458 1.146,1.635 0.177,0.177 10 *3
*1 Stopper *2 Nut
*3 Shift Lever Assembly - -



c.
C203381C11
1.813,1.01 1.677,0.479 1.677,0.479 1.573,0.479 true 1.844,2.229 1.76,1.917 1.76,1.917 1.667,1.917 false 2.448,2.094 2.365,1.792 2.365,1.792 2.469,1.792 false 2.344,1.135 2.427,1.448 2.427,1.448 2.521,1.448 false 1.354,0.385 1.531,0.552 0.177,0.167 10 *1 1.458,1.833 1.635,2 0.177,0.167 10 *1 2.49,1.698 2.698,1.885 0.208,0.188 10 *2 2.542,1.354 2.75,1.542 0.208,0.188 10 *2
*1 Slider
*2 Lock Piece


Slide the slider in the direction shown in the illustration and pull out the lock piece.


d.
C204586

Connect the end of the cable to the shift lever.

NOTICE:
·

Make sure that the lock piece is pulled up.


·

Push on the end of the cable all the way to the base of the pin.




e.

Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.


f.
C278980C01
0.781,0.531 0.677,0.146 0.677,0.146 0.563,0.146 true 0.396,0.073 0.708,0.271 0.313,0.198 10 *1 0.156,1.365 0.469,1.563 0.313,0.198 10 *a
*1 Adjuster Case
*a Push in


Push the lock piece into the adjuster case and lock it.

NOTICE:

Make sure that the lock piece is completely locked by the slider.