Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047091 AUTOMATIC TRANSAXLE ASSEMBLY A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 36100A 1.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT


a.

Clean the bolt holes.


b.

Apply adhesive 1324 to 2 or 3 threads on one half of a new transfer and transaxle setting stud bolt A as shown in the illustration.

C290575C01
0.479,2.021 0.792,2.219 0.313,0.198 10 false *a 4.146,0.417 4.458,0.615 0.313,0.198 10 false A 6,0.552 6.313,0.75 0.313,0.198 10 false B 2.677,0.885 2.99,1.083 0.313,0.198 10 false A 2.135,1.656 2.448,1.854 0.313,0.198 10 false B 0.479,2.323 0.792,2.521 0.313,0.198 10 false *b
*a Toyota Genuine Adhesive 1324 *b Sealant


Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:
·

Do not apply adhesive 1324 to the ends of the stud bolt.

·

Install the stud bolt immediately after applying adhesive to prevent the adherence of foreign matter.




c.

Install the 2 new transfer and transaxle setting stud bolts to the transaxle case positions shown in the illustration.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Install the stud bolt so that the side that has sealant and adhesive is facing the automatic transaxle assembly.


HINT:

Stud bolt length:

Stud bolt A: 69 mm (2.72 in.)

Stud bolt B: 47 mm (1.85 in.)



Hide 36100 2.INSTALL TRANSFER ASSEMBLY

Hide 3.INSTALL TORQUE CONVERTER ASSEMBLY

C209718

a.

Engage the splines of the input shaft and turbine runner.


b.
C209719

Engage the splines of the stator shaft and the stator while turning the torque converter assembly.

HINT:

If the stator shaft splines are difficult to engage with the stator splines, move the torque converter assembly back approximately 10 mm (0.394 in.) and engage the splines while rotating the torque converter assembly.



c.
C209720

Turn the torque converter assembly to insert the key of the oil pump drive gear into the groove of the torque converter assembly.


d.

Clean the torque converter assembly set bolt holes.


e.
C206480C01
1.167,0.917 1.26,0.292 1.26,0.292 1.354,0.292 true 1.198,2.406 1.115,3.021 1.115,3.021 1.01,3.021 true 2.781,1.552 2.698,2.167 2.698,2.167 2.594,2.167 true 2.531,0.969 2.448,1.583 2.448,1.583 2.344,1.583 true 2.177,0.521 2.313,0.698 0.135,0.177 10 A 1.385,0.198 1.563,0.375 0.177,0.177 10 *a 2.167,1.5 2.344,1.677 0.177,0.177 10 *a 0.781,2.938 0.958,3.115 0.177,0.177 10 *b 2.427,2.083 2.604,2.26 0.177,0.177 10 *b
*a Engine Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure dimension A between the transaxle contact surface of the engine and the torque converter assembly contact surface of the drive plate.

NOTICE:

Make sure to deduct the thickness of the straightedge.



f.
C206481E01
2.351,0.236 2.568,0.426 0.216,0.19 10 B

Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the previous step.

Standard distance:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Be sure to subtract the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 30500 4.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

C206482C01
2.547,0.404 2.811,0.63 0.265,0.226 12 *1 0.5,0.957 0.764,1.183 0.265,0.226 12 *2 1.435,0.991 2.375,0.504 2.375,0.504 2.472,0.504 false
*1 Torque Converter Assembly Centerpiece
*2 Crankshaft


a.

Apply clutch spline grease to the surface of the torque converter assembly center piece that contacts the crankshaft.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.
C209717N01
1.01,2.573 1.167,2.771 0.156,0.198 10 false A 0.802,2.823 0.958,3.021 0.156,0.198 10 false A 1.24,2.344 1.396,2.542 0.156,0.198 10 false B 2.531,2.469 2.688,2.667 0.156,0.198 10 false B 2.948,3.802 3.104,4 0.156,0.198 10 false A

Confirm that the 2 knock pins are on the surface of the engine block that contacts the transaxle.


c.

Maintain the engine and transaxle in a horizontal position, align the knock pins with each hole in the transaxle and install the transaxle with the 5 bolts shown in the illustration.

Torque:
for bolt A : 46 N*m (469 kgf*cm, 34 ft.*lbf)
for bolt B : 64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 5.INSTALL STIFFENER PLATE LH AND RH

a.
C279461N01
2.073,3.531 2.229,3.729 0.156,0.198 10 A 2.615,0.573 2.771,0.771 0.156,0.198 10 A 1.563,1.583 1.719,1.781 0.156,0.198 10 C 1.406,1.885 1.563,2.083 0.156,0.198 10 D 0.604,3.708 0.76,3.906 0.156,0.198 10 B 1.146,2.552 1.302,2.75 0.156,0.198 10 C 2.208,0.396 2.375,0.604 0.167,0.208 10 B 1.677,3.542 1.833,3.74 0.156,0.198 10 D

Temporarily install the stiffener plate LH and RH with the 8 bolts.


b.

While holding one stiffener plate against the transaxle, tighten bolt A, and then tighten bolts B, C and D. Perform the same procedure for the other stiffener plate.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 33403M 7.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

a.

Coat a new O-ring with ATF and install it to the speedometer driven hole cover sub-assembly.


b.

Install the speedometer driven hole cover sub-assembly with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 ft.*lbf)


Hide 33823 8.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 9.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket and with the bolt.

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)


Hide 17361J 10.INSTALL NO. 1 AIR TUBE

a.

Install the air tube support with the bolt.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


b.

Install the No. 1 air tube with the 2 bolts and tighten the clamp.

Torque:
for bolt : 24 N*m (245 kgf*cm, 18 ft.*lbf)
for clamp : 6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:

Before installation, remove any oil residue from the inside of the tube and hose.



Hide 12325A 11.INSTALL ENGINE MOUNTING BRACKET LH

a.

Clean the bolts and the installation holes in the engine mounting bracket LH.


b.

Apply adhesive to 2 or 3 threads on the ends of the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the engine mounting bracket LH to the transaxle with the 4 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


d.

Install the wire harness clamp bracket to the engine mounting bracket LH with the bolt.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


Hide 12321A 12.INSTALL REAR ENGINE MOUNTING BRACKET

a.

Install the rear engine mounting bracket to the automatic transaxle assembly with the 4 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 12311A 13.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine mounting bracket to the automatic transaxle assembly with the 4 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 35123A 14.INSTALL BREATHER TUBE BRACKET

a.

Install the breather tube bracket to the front engine mounting bracket with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Connect the breather hose to the breather tube.


Hide 15.INSTALL GROUND CABLE

a.

Install the ground cable to the automatic transaxle assembly with the bolt and attach the clamp.

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)


Hide 16.CONNECT WIRE HARNESS

a.

Connect the park/neutral position switch connector and TCM connector, and attach the 7 wire harness clamps to the transaxle.

HINT:

Turn the lock lever until the claw of the TCM connector makes a connection sound and secure the connector with lock lever.



b.

Install the bolt.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


Hide 28100 17.INSTALL STARTER ASSEMBLY

Hide 18.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 19.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Remove any adhesive remaining in the 6 bolt holes of the torque converter assembly and 6 drive plate and torque converter assembly setting bolts.


b.

Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley with SST.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

HINT:

First install the black-colored bolt, and then the remaining 5 silver-colored bolts.


SST
09213-58014  (91551-80840)
09330-00021  


d.

Install the flywheel housing under cover.


Hide 20.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary (Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION).