Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3090E _57 Power Source / Network _008434 NETWORKING _0047063 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1273  Sliding Roof ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the sliding roof drive gear sub-assembly and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1273 Sliding Roof ECU Communication Stop No communication between the sliding roof drive gear sub-assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Sliding roof drive gear sub-assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector

·

Instrument panel junction block assembly



WIRING DIAGRAM

B309040E02
2.969,1.771 4.635,2.198 1.667,0.427 10 Instrument Panel Junction Block Assembly 4.375,3.521 5.229,3.75 0.854,0.229 10 from Battery 0.708,5.458 2.333,5.708 1.625,0.25 10 : LIN Communication Line 2.479,1.135 2.823,1.354 0.344,0.219 10 LIN2 2.896,0.979 3.094,1.167 0.198,0.188 10 16 2.969,1.604 3.281,1.802 0.313,0.198 10 3D 4.917,0.99 5.229,1.188 0.313,0.198 10 54 1.615,3.969 1.927,4.167 0.313,0.198 10 12 1.875,4.052 2.031,4.25 0.156,0.198 10 E 0.844,2.552 3.729,2.75 2.885,0.198 10 Main Body ECU (Multiplex Network Body ECU) 0.875,2.344 1.031,2.542 0.156,0.198 10 A 2.729,3.531 2.885,3.729 0.156,0.198 10 B 2.49,4 3.104,4.198 0.615,0.198 10 MPX1 3.344,3.708 4.26,3.906 0.917,0.198 10 S/ROOF 1.198,4.563 1.51,4.76 0.313,0.198 10 Q8 1.198,4.76 3.552,4.99 2.354,0.229 10 Sliding Roof Drive Gear Sub-assembly 2.938,3.854 3.25,4.052 0.313,0.198 10 11 2.958,3.427 3.115,3.625 0.156,0.198 10 8

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



HINT:

When the communication between the sliding roof drive gear sub-assembly and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


PROCEDURE

1.CLEAR DTC

Body Electrical > Main Body > Clear DTCs
50002 123
Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Proceed to
DTC B1273 is output
DTC B1273 is not output



DTC B1273 is output

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

DTC B1273 is not output

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Disconnect the Q8 sliding roof drive gear sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - Q8-11 (MPX1) Always Below 1 Ω
A-16 (LIN2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - BATTERY AND BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
B295816C06
1.531,0.344 1.906,0.563 0.375,0.219 0.813,1.802 1.229,1.385 false 2.188,1.375 2.677,1.76 false 1.615,0.365 1.927,0.563 0.313,0.198 10 Q8 0.635,1.771 0.792,1.969 0.156,0.198 10 B 2.76,1.698 2.917,1.896 0.156,0.198 10 E 0.083,0.073 0.396,0.271 0.313,0.198 10 *a
*a Front view of wire harness connector
(to Sliding Roof Drive Gear Sub-assembly)


Disconnect the Q8 sliding roof drive gear sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q8-12 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Q8-8 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
a.

Temporarily replace the sliding roof drive gear sub-assembly with a new or normally functioning one.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING>DISASSEMBLY



Body Electrical > Main Body > Clear DTCs
50002 123
Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

Result:
Proceed to
DTC B1273 is not output
DTC B1273 is output (for LHD)
DTC B1273 is output (for RHD)



DTC B1273 is not output

END (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY IS DEFECTIVE)

DTC B1273 is output (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

DTC B1273 is output (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Disconnect the Q8 sliding roof drive gear sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-54 - Q8-11 (MPX1) Always Below 1 Ω
3D-54 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

OK (for RHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR