Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3090E _57 Power Source / Network _008434 NETWORKING _0047063 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU intermittently monitors the LIN communication bus between the components related to certification. DTC B2785 is stored when a malfunction in the LIN communication bus between the components related to certification is detected 3 times consecutively.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN The certification ECU detects a malfunction in the LIN communication bus between components related to certification 3 times consecutively.
·

Certification ECU (smart key ECU assembly)

·

ID code box (immobiliser code ECU)

·

Steering lock actuator assembly

·

Harness or connector



WIRING DIAGRAM

B301186E02
0.594,1.406 2.719,1.823 2.125,0.417 10 Certification ECU (Smart Key ECU assembly) 0.604,1.219 1.063,1.417 0.458,0.198 10 G84 1.854,0.75 2.313,0.948 0.458,0.198 10 LIN 2.135,0.583 2.448,0.781 0.313,0.198 10 17 5.094,0.74 5.708,0.938 0.615,0.198 10 LIN1 4.906,0.594 5.063,0.792 0.156,0.198 10 2 4.75,1.198 5.208,1.396 0.458,0.198 10 G44 4.76,1.385 6.302,1.74 1.542,0.354 10 ID Code Box (Immobliser Code ECU) 4.927,2.292 5.083,2.49 0.156,0.198 10 5 5.104,2.427 5.563,2.625 0.458,0.198 10 LIN 4.479,2.917 4.792,3.115 0.313,0.198 10 G5 4.479,3.094 6.594,3.406 2.115,0.313 10 Steering Lock Actuator Assembly 0.698,3.427 4.365,3.625 3.667,0.198 10 : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

·

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU), refer to the entry and start system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION



HINT:

When DTC B2785 and B2287 are output simultaneously, perform troubleshooting for DTC B2785 first.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is output
DTC B2785 is not output



DTC B2785 is output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ID CODE BOX [IMMOBILISER CODE ECU] OR STEERING LOCK ACTUATOR ASSEMBLY)

DTC B2785 is not output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ID CODE BOX [IMMOBILISER CODE ECU] OR STEERING LOCK ACTUATOR ASSEMBLY)
a.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G44 ID code box (immobiliser code ECU) connector.


c.

Disconnect the G5 steering lock actuator assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-17 (LIN) - G5-5 (LIN) Always Below 1 Ω
G84-17 (LIN) - G44-2 (LIN1) Always Below 1 Ω
G84-17 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Disconnect the G5 steering lock actuator assembly connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

6.CLEAR DTC

DTC B2785 is output

REPLACE STEERING LOCK ACTUATOR ASSEMBLY

6.CLEAR DTC
a.

Disconnect the G44 ID code box (immobiliser code ECU) connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

DTC B2785 is output

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)