Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type)
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047060 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Clearance Warning ECU Power Source Circuit  


DESCRIPTION

When the telltale light assembly (clearance sonar main switch) is turned on, the on signal is input into the clearance warning ECU assembly.

WIRING DIAGRAM

E270582
0.365,0.854 1.875,1.052 1.51,0.198 10 from IG1 NO. 1 Relay 2.021,1.063 2.958,1.25 0.938,0.188 10 ECU-IG NO. 1 3.125,1.573 5.021,1.969 1.896,0.396 10 Telltale Light Assembly (Clearance Sonar Main Switch) 3.135,1.385 3.458,1.563 0.323,0.177 10 G43 5.438,1.771 5.896,1.969 0.458,0.198 10 G33 5.448,1.958 6.635,2.354 1.188,0.396 10 Clearance Warning ECU Assembly 5.302,0.74 5.615,0.938 0.313,0.198 10 11 4.667,0.75 4.979,0.948 0.313,0.198 10 1 4.26,0.854 4.667,1.052 0.406,0.198 10 ECU 3.385,0.74 3.542,0.938 0.156,0.198 10 9 3.573,0.865 4.188,1.063 0.615,0.198 10 LAPB 5.552,0.875 5.958,1.073 0.406,0.198 10 IG

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - BATTERY)
a.
E270586
1.5,0.302 1.938,0.573 0.438,0.271 2.083,1.25 2.719,0.531 false 0.094,0.083 0.406,0.281 0.313,0.198 10 *a 1.583,0.354 1.958,0.552 0.375,0.198 10 G43 2.813,0.438 3.333,0.615 0.521,0.177 10 LAPB
*a Front view of wire harness connector
(to Telltale Light Assembly)


Disconnect the telltale light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G43-9 (LAPB) - Body ground Ignition switch ON 11 to 14 V
G43-9 (LAPB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the G43 telltale light assembly connector.


b.

Disconnect the G33 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G43-1 (ECU) - G33-11 (IG) Always Below 1 Ω
G43-1 (ECU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TELLTALE LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TELLTALE LIGHT ASSEMBLY


Result:
Proceed to
OK
NG



OK

NG