Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047058 BLIND SPOT MONITOR SYSTEM Y

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the blind spot monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*

Result:
Proceed to
CAN communication system DTC is not output.
CAN communication system (for LHD) DTC is output.
CAN communication system (for RHD) DTC is output.



CAN communication system DTC is not output.

5.CHECK FOR DTC AND FREEZE FRAME DATA*

CAN communication system (for LHD) DTC is output.

CAN communication system (for RHD) DTC is output.

5.CHECK FOR DTC AND FREEZE FRAME DATA*
a.

Refer to DTC Check / Clear for the blind spot monitor system.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314
Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313

b.

Record or print DTCs and freeze frame data, if necessary.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>FREEZE FRAME DATA


Result:
Proceed to
DTCs are output.
DTCs are not output.



DTCs are output.

6.CLEAR DTC*

DTCs are not output.

9.PERFORM SYMPTOMS TABLE
6.CLEAR DTC*
a.

Refer to DTC Check / Clear for the blind spot monitor system.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

HINT:

The current DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.


Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313
Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

Result:
Proceed to
NEXT



NEXT

7.RECHECK FOR DTC*
7.RECHECK FOR DTC*
a.

Refer to DTC Check / Clear for the blind spot monitor system.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
HINT:

Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.



Result:
Proceed to
DTCs are output.
DTCs are not output.



DTCs are output.

8.DIAGNOSTIC TROUBLE CODE CHART

DTCs are not output.

9.PERFORM SYMPTOMS TABLE
8.DIAGNOSTIC TROUBLE CODE CHART

Result:
Proceed to
NEXT



NEXT

11.CIRCUIT INSPECTION
9.PERFORM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE

HINT:

If the symptom does not recur and no DTC is output, attempt to reproduce the symptoms

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Proceed to
Fault is not listed in Problem Symptoms Table.
Fault is listed in Problem Symptoms Table.



Fault is not listed in Problem Symptoms Table.

10.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

Fault is listed in Problem Symptoms Table.

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE ADJUSTING LOCK NUT

10.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

NEXT

11.CIRCUIT INSPECTION
11.CIRCUIT INSPECTION
Result:
Proceed to
NEXT



NEXT

12.ADJUST, REPAIR OR REPLACE
12.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

13.PERFORM BEAM AXIS INSPECTION AND CONFIRMATION
13.PERFORM BEAM AXIS INSPECTION AND CONFIRMATION
a.

Enter Test Mode (refer to Blind Spot Monitor Beam Axis Inspection).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK


b.

Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK


Result:
Proceed to
NEXT



NEXT

14.PERFORM CONFIRMATION TEST*
14.PERFORM CONFIRMATION TEST*
Result:
Proceed to
NEXT



NEXT

END