Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2012.12–2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047058 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1A45  Vehicle Speed Sensor  


DESCRIPTION

The blind spot monitor sensor receives vehicle speed signals from the brake actuator assembly via CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A45 Vehicle Speed Sensor A fail flag is transmitted from the brake actuator assembly.
·

Anti-lock brake system (w/o VSC)

·

Vehicle stability control system (w/ VSC)

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH



CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) is on.

*1: for LHD

*2: for RHD



PROCEDURE

1.CHECK BRAKE CONTROL SYSTEM
a.

Check brake control system.


Result:
Proceed to
w/o VSC
w/ VSC



w/o VSC

2.CHECK OTHER DTC OUTPUT (ANTI-LOCK BRAKE SYSTEM)

w/ VSC

4.CHECK OTHER DTC OUTPUT (VEHICLE STABILITY CONTROL SYSTEM)
2.CHECK OTHER DTC OUTPUT (ANTI-LOCK BRAKE SYSTEM)
a.

Check for anti-lock brake system DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Proceed to
Anti-lock brake system DTCs are not output
Anti-lock brake system DTCs are output



Anti-lock brake system DTCs are not output

3.CHECK DTC

Anti-lock brake system DTCs are output

3.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
No DTC is output
DTC is output from the blind spot monitor sensor LH (master)
DTC is output from the blind spot monitor sensor RH (slave)




No DTC is output

DTC is output from the blind spot monitor sensor LH (master)

DTC is output from the blind spot monitor sensor RH (slave)

4.CHECK OTHER DTC OUTPUT (VEHICLE STABILITY CONTROL SYSTEM)
a.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
Vehicle stability control system DTCs are not output
Vehicle stability control system DTCs are output



Vehicle stability control system DTCs are not output

5.CHECK DTC

Vehicle stability control system DTCs are output

5.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
No DTC is output
DTC is output from the blind spot monitor sensor LH (master)
DTC is output from the blind spot monitor sensor RH (slave)




No DTC is output

DTC is output from the blind spot monitor sensor LH (master)

DTC is output from the blind spot monitor sensor RH (slave)