Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2012.12–2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047058 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH judges that there is a communication problem with the blind spot monitor sensor RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0232 Lost Communication with Blind Spot Monitor Slave Module The blind spot monitor sensor LH cannot receive signals from the blind spot monitor sensor RH.
·

CAN communication Line

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E233765E09
3.052,1.208 3.365,1.385 0.313,0.177 10 false BRB 2.875,1.094 2.99,1.271 0.115,0.177 10 false 5 2.813,2.49 2.99,2.667 0.177,0.177 10 false 10 3.052,2.625 3.531,2.781 0.479,0.156 10 false BRGB 1.844,1.417 2.427,1.625 0.583,0.208 10 false GAUGE 0.083,1.229 1.063,1.552 0.979,0.323 10 false from IG1 NO. 2 Relay 2.583,3.302 2.948,3.458 0.365,0.156 10 false T1 2.583,3.49 4.469,3.667 1.885,0.177 9 false Blind Spot Monitor Sensor RH 5,3.313 5.365,3.469 0.365,0.156 10 false R1 3.531,1.573 3.927,1.75 0.396,0.177 10 false CA2P 3.531,1.917 3.927,2.094 0.396,0.177 10 false CA2N 4,1.438 4.115,1.615 0.115,0.177 10 false 1 4,1.781 4.115,1.958 0.115,0.177 10 false 6 5.229,1.438 5.344,1.615 0.115,0.177 10 false 1 5.229,1.792 5.344,1.969 0.115,0.177 10 false 6 5.396,1.563 5.792,1.74 0.396,0.177 10 false CA2P 5.396,1.917 5.792,2.094 0.396,0.177 10 false CA2N 0.865,4.021 3.146,4.198 2.281,0.177 10 false : CAN Communication Line 5,3.479 6.979,3.698 1.979,0.219 10 false Blind Spot Monitor Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly*1 or telltale light assembly*2) is on.

*1: for LHD

*2: for RHD


·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the T1 blind spot monitor sensor RH connector.


b.

Disconnect the R1 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-1 (CA2P) - R1-1 (CA2P) Always Below 1 Ω
T1-6 (CA2N) - R1-6 (CA2N) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE CAN LINE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
E263038C03
1.49,0.26 1.802,0.469 0.313,0.208 2,1.146 2.51,0.51 2.51,0.51 2.708,0.51 false 0.083,0.052 0.396,0.25 0.313,0.198 10 *a 1.573,0.292 1.885,0.49 0.313,0.198 10 T1 2.781,0.427 3.188,0.615 0.406,0.188 10 BRB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
T1-5 (BRB) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
E263038C10
1.49,0.25 1.833,0.479 0.344,0.229 2,1.354 2.448,1.823 2.448,1.823 2.646,1.823 false 0.083,0.052 0.396,0.25 0.313,0.198 10 *a 1.573,0.292 1.885,0.49 0.313,0.198 10 T1 2.729,1.74 3.25,1.938 0.521,0.198 10 BRGB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-10 (BRGB) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE BLIND SPOT MONITOR SENSOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE BLIND SPOT MONITOR SENSOR RH
a.

Temporarily replace the blind spot monitor sensor RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC
5.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Clear DTCs
50002 313
Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

Result:
Proceed to
No DTCs are output
DTCs are output



No DTCs are output

END (BLIND SPOT MONITOR SENSOR RH IS DEFECTIVE)

DTCs are output