Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008429 LIGHTING (INT) _0047052 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the ignition key cylinder light (w/o Entry and Start System), map light and No. 1 room light.

WIRING DIAGRAM

E270022E01
1.667,4.813 3.594,5.052 1.927,0.24 10 No. 1 Room Light Assembly 0.188,8.354 2.115,8.594 1.927,0.24 10 *2: w/o Sliding Roof System 0.188,8.01 2.115,8.25 1.927,0.24 10 *1: w/ Sliding Roof System 4.375,7.135 5.979,7.563 1.604,0.427 10 Instrument Panel Junction Block Assembly 4.365,6.979 4.615,7.198 0.25,0.219 10 3D 4.927,7.719 5.177,7.938 0.25,0.219 10 A 4.917,7.875 7.073,8.333 2.156,0.458 10 Main Body ECU (Multiplex Network Body ECU) 0.323,5.292 2.615,5.531 2.292,0.24 12 w/o Entry and Start System: 0.344,5.865 1.292,6.073 0.948,0.208 10 from Battery 2.469,6.219 4.583,6.594 2.115,0.375 10 Transponder Key Coil (Ignition Key Cylinder Light) 2.656,5.781 2.906,6 0.25,0.219 10 2 2.458,6.073 2.708,6.292 0.25,0.219 10 G6 3.833,5.781 4.052,5.979 0.219,0.198 10 4 3.51,5.875 3.844,6.063 0.333,0.188 10 ILL- 2.813,5.885 3.146,6.073 0.333,0.188 10 ILL+ 2.531,3.552 3.052,3.74 0.521,0.188 10 DOOR 1.844,6.021 2.365,6.208 0.521,0.188 10 DOME 4.896,5.781 5.115,5.979 0.219,0.198 10 44 5.875,5.781 6.094,5.979 0.219,0.198 10 26 6.115,5.875 6.542,6.063 0.427,0.188 10 KILE 3.281,3.635 3.667,3.813 0.385,0.177 10 CTY 2.917,4.01 3.313,4.198 0.396,0.188 10 OFF 2.75,4.458 3.104,4.646 0.354,0.188 10 ON 3.448,4.208 3.719,4.396 0.271,0.188 10 E 2.688,2.198 3.042,2.385 0.354,0.188 10 ON 2.583,1.635 2.979,1.823 0.396,0.188 10 OFF 2.573,0.667 2.969,0.854 0.396,0.188 10 OFF 2.688,1.24 3.042,1.427 0.354,0.188 10 ON 4.021,1.781 4.417,1.969 0.396,0.188 10 OFF 6.135,1.573 6.563,1.76 0.427,0.188 10 ILE 5.927,1.458 6.146,1.656 0.219,0.198 10 1 4.896,1.49 5.115,1.688 0.219,0.198 10 35 4.198,1.479 4.583,1.625 0.385,0.146 10 CTY 4.552,1.479 4.771,1.677 0.219,0.198 10 2 3.688,1.271 4.208,1.458 0.521,0.188 10 DOOR 0.615,0.833 0.833,1.031 0.219,0.198 10 3 0.604,2.292 0.823,2.49 0.219,0.198 10 1 0.792,2.292 1.24,2.479 0.448,0.188 10 GND 0.802,0.844 1.229,1.031 0.427,0.188 10 +B1 0.76,2.833 1.917,3.052 1.156,0.219 10 Q12*1, Q11*2 0.781,3.01 2.333,3.229 1.552,0.219 10 Map Light Assembly 1.677,3.792 1.938,3.99 0.26,0.198 10 B 1.354,0.146 3.073,0.365 1.719,0.219 10 from DOME CUT Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MAP LIGHT, NO. 1 ROOM LIGHT AND IGNITION KEY CYLINDER LIGHT)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Illuminated Entry System Map light, ignition key cylinder light (w/o Entry and Start System) and No. 1 room light ON or OFF Turn the map light switch and No. 1 room light switch to the DOOR position.
Body Electrical > Main Body > Active Test
Tester Display
Illuminated Entry System
50004 123 4

Result:
Result Proceed to
Map light assembly, No. 1 room light assembly and ignition key cylinder light comes on A
Map light assembly and No. 1 room light assembly does not comes on B
Map light assembly or No. 1 room light assembly does not comes on C
Ignition key cylinder light does not comes on (w/o Entry and Start System) D



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT MAP LIGHT ASSEMBLY

C

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

D

6.INSPECT TRANSPONDER KEY COIL (IGNITION KEY CYLINDER LIGHT)
2.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE MAP LIGHT ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - BATTERY AND BODY GROUND)
a.
E270023C01
0.198,0.688 0.646,0.969 0.448,0.281 0.208,1.042 0.656,1.323 0.448,0.281 1.083,1.604 1.417,1.281 false 2.417,1.604 2.073,1.281 false 0.698,0.698 1.01,0.854 0.313,0.156 10 *A 0.708,1.052 1.021,1.208 0.313,0.156 10 *B 0.281,0.771 0.74,0.969 0.458,0.198 10 Q12 0.281,1.083 0.74,1.281 0.458,0.198 10 Q11 0.896,1.625 1.354,1.823 0.458,0.198 10 GND 2.365,1.646 2.823,1.844 0.458,0.198 10 +B1
*A w/ Sliding Roof System
*B w/o Sliding Roof System


Disconnect the map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Sliding Roof System:
Tester Connection Condition Specified Condition
Q12-3 (+B1) - Body ground Battery saving control (interior light auto cut function) not operating 11 to 14 V

w/o Sliding Roof System:
Tester Connection Condition Specified Condition
Q11-3 (+B1) - Body ground Battery saving control (interior light auto cut function) not operating 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Sliding Roof System:
Tester Connection Condition Specified Condition
Q12-1 (GND) - Body ground Always Below 1 Ω

w/o Sliding Roof System:
Tester Connection Condition Specified Condition
Q11-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the Q12*1 or Q11*2 map light assembly connector.

*1: w/ Sliding Roof System

*2: w/o Sliding Roof System


b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Sliding Roof System:
Tester Connection Condition Specified Condition
Q12-2 (CTY) - 3D-35 Always Below 1 Ω
Q12-2 (CTY) - Body ground Always 10 kΩ or higher

w/o Sliding Roof System:
Tester Connection Condition Specified Condition
Q11-2 (CTY) - 3D-35 Always Below 1 Ω
Q11-2 (CTY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
E270727N02
0.156,0.99 0.552,1.208 0.396,0.219 1.417,2.25 1.813,2.469 0.396,0.219 0.458,2.938 0.458,2.719 false 0.26,1.021 0.594,1.219 0.333,0.198 10 3D 0.375,2.958 0.708,3.156 0.333,0.198 10 ILE 1.563,2.281 1.896,2.479 0.333,0.198 10 A

Remove the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (ILE) - 3D-35 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT TRANSPONDER KEY COIL (IGNITION KEY CYLINDER LIGHT)
a.

Remove the transponder key coil (ignition key cylinder light).

Click hereVehicle Interior>LIGHTING (INT)>IGNITION KEY CYLINDER LIGHT>REMOVAL


b.

Inspect the transponder key coil (ignition key cylinder light).

Click hereVehicle Interior>LIGHTING (INT)>IGNITION KEY CYLINDER LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY COIL [IGNITION KEY CYLINDER LIGHT] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BATTERY)

NG

REPLACE TRANSPONDER KEY COIL (IGNITION KEY CYLINDER LIGHT)

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY COIL [IGNITION KEY CYLINDER LIGHT] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BATTERY)
a.

Disconnect the G6 transponder key coil (ignition key cylinder light) connector.


b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G6-2 (ILL+) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-4 (ILL-) - 3D-44 Always Below 1 Ω
G6-4 (ILL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
E270727N01
0.115,0.969 0.479,1.219 0.365,0.25 1.417,2.198 1.781,2.448 0.365,0.25 2.458,2.979 2.458,2.74 false 0.198,1.021 0.51,1.219 0.313,0.198 10 3D 1.563,2.24 1.875,2.438 0.313,0.198 10 A 2.313,3 2.708,3.188 0.396,0.188 10 KILE

Remove the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD:

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-26 (KILE) - 3D-44 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG