31204
1.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY
31230
2.REMOVE CLUTCH RELEASE BEARING ASSEMBLY
31236B
3.REMOVE RELEASE FORK SUPPORT
31126
4.REMOVE CLUTCH RELEASE FORK BOOT
Remove the clutch release fork boot from the front transaxle assembly.
33524B
5.REMOVE CONTROL CABLE BRACKET
Remove the 3 bolts and cable bracket from the manual transaxle assembly.
33590F
6.REMOVE FLOOR SHIFT SELECTING BELL CRANK ASSEMBLY
Remove the 2 bolts and floor shift selecting bell crank assembly from the manual transaxle assembly.
84210
7.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY
Using SST, remove the back-up light switch assembly and gasket.
84545
8.REMOVE NEUTRAL POSITION SWITCH
Using SST, remove the neutral position switch and gasket.
33290
9.REMOVE NO. 1 LOCK BALL ASSEMBLY
Remove the No. 1 lock ball assembly from the manual transmission case.
33290B
10.REMOVE NO. 2 LOCK BALL ASSEMBLY
Remove the No. 2 lock ball assembly from the manual transmission case.
33295B
11.REMOVE SHIFT GATE PIN
Remove the shift gate pin from the manual transmission case.
33251A
12.REMOVE SHIFT AND SELECT LEVER ASSEMBLY
Remove the 4 bolts and shift and select lever assembly from the manual transmission assembly.
33261F
13.REMOVE SHIFT AND SELECT LEVER SHAFT STRAIGHT PIN
While pressing in the shift and select lever shaft straight pin (A) as far as it will go, pull out the shift and select lever shaft straight pin (B) to remove it.
Remove the spring.
33403L
14.REMOVE O-RING
Remove the O-ring from the shift and select lever shaft straight pin (B).
33101A
15.REMOVE MANUAL TRANSMISSION FILLER PLUG
Remove the manual transmission filler plug and gasket from the manual transmission case.
33104
16.REMOVE DRAIN PLUG
Remove the drain plug and gasket from the front transaxle case.
33275C
17.REMOVE SHIFT DETENT BALL
Using a 6 mm hexagon wrench, remove the 4 detent ball plugs from the front transaxle case.
Using a magnet hand, remove the 4 No. 1 shift detent ball spring seats, 4 shift detent ball compression springs and 4 shift detent balls.
18.REMOVE REVERSE IDLER GEAR SHAFT BOLT
Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.
33111A
19.REMOVE MANUAL TRANSMISSION CASE PLUG
Remove the 2 manual transmission case plugs from the manual transmission case.
33111
20.REMOVE MANUAL TRANSMISSION CASE
Remove the 6 bolts from the front transaxle case.
Remove the 12 bolts from the manual transmission case.
Using 2 pairs of snap ring pliers to keep the snap ring stretched, remove the manual transmission case.
33124C
21.REMOVE NO. 1 OIL RECEIVER PIPE
Remove the No. 1 oil receiver pipe from the manual transmission case.
Do not damage the No. 1 oil receiver pipe.
33176B
22.REMOVE TRANSMISSION OIL SEPARATOR
for Manual Transmission Case Side:
Remove the 2 bolts and transmission oil separator from the manual transmission case.
33242F
23.REMOVE 1ST AND 2ND SHIFT FORK SHAFT
Remove the bolt from the No. 1 gear shift fork.
Remove the 1st and 2nd shift fork shaft.
33243F
24.REMOVE 3RD AND 4TH SHIFT FORK SHAFT
Using a 5 mm pin punch and hammer, tap out the pin from the No. 2 gear shift head.
Using a 5 mm pin punch and hammer, tap out the pin from the No. 2 gear shift fork.
| *1 | 3rd and 4th Shift Fork Shaft |
| *2 | No. 2 Gear Shift Head |
Remove the 3rd and 4th shift fork shaft and No. 2 gear shift head.
33213G
25.REMOVE NO. 2 GEAR SHIFT FORK
Remove the No. 2 gear shift fork from the No. 1 output shaft assembly.
33246C
26.REMOVE NO. 5 GEAR SHIFT FORK SHAFT
Using a screwdriver, remove the E-ring from the pin.
Remove the pin from the shift arm.
Remove the No. 5 gear shift fork shaft from the front transaxle case.
Using a 5 mm pin punch and hammer, tap out the pin.
Remove the No. 3 gear shift head from the No. 5 gear shift fork shaft.
33212A
27.REMOVE NO. 1 GEAR SHIFT FORK
Remove the No. 1 gear shift fork from the No. 1 output shaft assembly.
33222F
28.REMOVE SHIFT ARM
Remove the shift arm from the front transaxle case.
33245H
29.REMOVE REVERSE SHIFT FORK SHAFT
Remove the bolt from the reverse shift fork.
Remove the reverse shift fork shaft from the front transaxle case.
33244J
30.REMOVE 5TH AND 6TH SHIFT FORK SHAFT
Remove the bolt from the No. 3 gear shift fork.
Remove the 5th and 6th shift fork shaft from the front transaxle case.
33214G
31.REMOVE NO. 3 GEAR SHIFT FORK
Remove the No. 3 gear shift fork from the No. 2 output shaft assembly.
33211
32.REMOVE REVERSE SHIFT FORK
Remove the reverse shift fork from the No. 2 output shaft assembly.
33.INSPECT REVERSE IDLER GEAR THRUST CLEARANCE
34.INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE
33461
35.REMOVE REVERSE IDLER GEAR
Remove the reverse idler gear shaft by sliding and lifting it.
Remove the reverse idler gear, needle roller bearing and reverse idler thrust washer from the reverse idler gear shaft.
33311
36.REMOVE INPUT SHAFT, NO. 1 OUTPUT SHAFT ASSEMBLY AND NO. 2 OUTPUT SHAFT ASSEMBLY
Remove the 3 shafts at the same time.
Do not drop the input shaft, No. 1 output shaft assembly and No. 2 output shaft assembly.
33176B
37.REMOVE TRANSMISSION OIL SEPARATOR
for Front Transaxle Case Side:
Remove the 2 bolts and transmission oil separator from the front transaxle case.
41301L
38.REMOVE FRONT DIFFERENTIAL CASE ASSEMBLY
Remove the front differential case assembly from the front transaxle case.
33449
39.REMOVE TRANSMISSION MAGNET
Remove the transmission magnet from the front transaxle case.
33322A
40.REMOVE REAR NO. 2 OUTPUT SHAFT BEARING OUTER RACE
| *a | Turn |
| *b | Hold |
Using SST, remove the rear No. 2 output shaft bearing outer race the manual transmission case to remove it.
33321H
41.REMOVE REAR OUTPUT SHAFT BEARING SHIM
Remove the rear output shaft bearing shim from the manual transmission case.
33242L
42.REMOVE SHIFT FORK SHAFT BEARING
Using SST, remove the 4 shift fork shaft bearings from the manual transmission case to remove them.
33261K
43.REMOVE SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING
Using SST, remove the shift and select lever shaft needle roller bearing from the manual transmission case to remove it.
33311P
44.REMOVE REAR INPUT AND OUTPUT SHAFT BEARING SHAFT SNAP RING
Using a snap ring expander, remove the rear input and output shaft bearing shaft snap rings.
33311A
45.REMOVE FRONT INPUT SHAFT BEARING
Remove the bolt and bearing lock plate from the front transaxle case.
| *a | Turn |
| *b | Hold |
Using SST, remove the front input shaft bearing from the front transaxle case to remove it.
31105H
46.REMOVE TRANSAXLE CASE OIL SEAL
| *a | Protective Tape |
Using a screwdriver, remove the transaxle case oil seal from the front transaxle case.
Do not damage the installation surface of the front transmission case.
Tape the screwdriver tip before use.
33321N
47.REMOVE FRONT OUTPUT SHAFT BEARING
Remove the bolt and bearing lock plate from the front transaxle case.
| *a | Turn |
| *b | Hold |
Using SST, remove the front output shaft bearing from the front transaxle case to remove it.
33134B
48.REMOVE OUTPUT SHAFT COVER
Remove the output shaft cover from the front transaxle case.
33322B
49.REMOVE FRONT NO. 2 OUTPUT SHAFT BEARING OUTER RACE
| *a | Turn |
| *b | Hold |
Using SST, remove the front No. 2 output shaft bearing outer race from the front transaxle case to remove it.
33134B
50.REMOVE OUTPUT SHAFT COVER
Remove the output shaft cover from the front transaxle case.
33111J
51.REMOVE MANUAL TRANSMISSION CASE STRAIGHT PIN
Remove the 4 manual transmission case straight pin.
33242L
52.REMOVE SHIFT FORK SHAFT BEARING
Using SST, remove the 4 shift fork shaft bearings from the front transaxle case to remove them.
31105H
53.REMOVE TRANSMISION CASE OIL SEAL
41311F
54.REMOVE FRONT DIFFERENTIAL CASE REAR OUTER RACE BEARING
Using a brass bar and hammer, tap out the front differential case rear outer race bearing and front differential case rear shim from the manual transmission case.
31105H
55.REMOVE TRANSAXLE CASE OIL SEAL
41311E
56.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
Using SST, remove the front differential case frontbearing outer race from the front transaxle case.