Home › Drivetrain › EA64 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT
RM3090E _52 Drivetrain _008755 EA64 MANUAL TRANSMISSION / TRANSAXLE _0048557 OUTPUT SHAFT A

EA64 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  REASSEMBLY  


PROCEDURE

Hide 33322B 1.INSTALL NEEDLE ROLLER BEARING

a.
C112406

Coat the needle roller bearing with gear oil, and install it into the No. 2 output shaft.


Hide 33331 2.INSTALL REVERSE DRIVEN GEAR

a.
C277853

Coat the reverse driven gear with gear oil, and install it into the No. 2 output shaft.


Hide 33352B 3.INSTALL NO. 4 TRANSMISSION CLUTCH HUB

a.
C116552C02
0.677,0.594 0.677,0.25 0.677,0.25 0.844,0.25 false 1.927,0.896 1.927,0.448 1.927,0.448 2.156,0.448 false 2.521,0.656 2.271,0.656 2.271,0.656 2.271,1.094 false 2.854,0.865 2.656,0.865 2.656,0.865 2.656,1.146 false 2.125,3.521 1.76,3.521 false 0.656,3.177 0.656,2.542 0.656,2.542 0.865,2.542 false 1.729,1.677 1.729,1.885 1.729,1.885 1.458,1.885 false 1.438,0.792 1.438,0.208 1.438,0.208 1.729,0.208 false 0.948,2.448 1.26,2.646 0.313,0.198 10 *a 1.563,3.417 1.875,3.615 0.313,0.198 10 *a 2.917,0.771 3.229,0.969 0.313,0.198 10 *1 2.583,0.563 2.896,0.76 0.313,0.198 10 *2 2.229,0.354 2.542,0.552 0.313,0.198 10 *3 1.813,0.115 2.125,0.313 0.313,0.198 10 *4 0.927,0.188 1.24,0.385 0.313,0.198 10 *5 1.229,1.823 1.542,2.021 0.313,0.198 10 *3
*1 No. 4 Transmission Clutch Hub
*2 Key Spring
*3 Shifting Key
*4 Reverse Driven Gear Synchronizer Ring
*5 No. 4 Transmission Hub Sleeve
*a Claw


Install the key spring and 2 shifting keys to the No. 4 transmission clutch hub.

HINT:
·

Install the shifting key with the grooves on the clutch hub side.

·

Install the key spring with the claw on the clutch hub side.

·

Refer to the illustration when installing the key spring and shifting keys.




b.

Install the No. 4 transmission hub sleeve to the reverse driven gear as shown in the illustration.


c.
C116199E01
0.259,1.001 0.6,1.34 0.34,0.34 10 SST 0.659,1.081 0.805,1.081 0.805,1.081 1.13,1.313 false

Coat the No. 4 transmission clutch hub with gear oil, and install it into the No. 2 output shaft.


d.

Using SST and a press, press in the reverse driven gear and No. 4 transmission clutch hub into the No. 2 output shaft.

SST
09308-14010  

NOTICE:

After installation, make sure that the gear and synchronizer ring move smoothly.


HINT:

Make sure that the protruding part on the synchronizer ring is fitted into the groove of the clutch hub.



Hide 33352C 4.INSTALL SHAFT SNAP RING

a.
C277854C01
3.104,1.146 3.104,0.979 3.104,0.979 2.5,0.885 false 3.021,1.198 3.333,1.396 0.313,0.198 10 *a
*a Mark


Select a new shaft snap ring, using the table below, that makes the thrust clearance of the No. 4 transmission clutch hub less than 0.1 mm (0.00394 in.).

Standard shaft snap ring thickness:
Mark Thickness Mark Thickness
A 2.25 mm (0.0886 in.) E 2.45 mm (0.0965 in.)
B 2.30 mm (0.0906 in.) F 2.50 mm (0.0984 in.)
C 2.35 mm (0.0925 in.) G 2.55 mm (0.100 in.)
D 2.40 mm (0.0945 in.) H 2.60 mm (0.102 in.)



b.
C112456

Using a brass bar and hammer, tap the shaft snap ring onto the No. 2 output shaft.


Hide 5.INSPECT REVERSE DRIVEN GEAR THRUST CLEARANCE

Hide 6.INSPECT REVERSE DRIVEN GEAR RADIAL CLEARANCE

Hide 33428C 7.INSTALL 5TH DRIVEN GEAR

a.
C112402

Install the 5th gear bearing spacer into the No. 2 output shaft.


b.
C112401

Coat the 2 pieces of the 5th gear needle roller bearing with gear oil, and install them into the No. 2 output shaft.


c.
C112400

Install the output shaft collar into the No. 2 output shaft.


d.
C116206

Coat the 5th driven gear with gear oil, and install it into the No. 2 output shaft.


Hide 33393 8.INSTALL NO. 3 TRANSMISSION CLUTCH HUB

a.
C116553

Apply of gear oil to the sleeve and hub.


b.

Install the hub sleeve to the clutch hub.


c.

Install the 3 shifting keys to the clutch hub.


d.

Install the 3 shifting key springs to the clutch hub.


e.

Place the 3 balls in the holes of the shifting keys, and install the hub sleeve while pushing in the balls.

NOTICE:

Take care to prevent the balls from scattering.



f.
C116200E01
0.645,0.215 1.01,0.55 0.366,0.336 10 SST 1.016,0.312 1.218,0.312 1.218,0.312 1.512,0.652 false

Coat the 5th driven gear synchronizer ring with gear oil, and install it to the 5th driven gear.


g.

Using SST and a press, press in the No. 3 transmission clutch hub to the No. 2 output shaft.

SST
09308-14010  

NOTICE:

After installation, make sure that the gear and synchronizer ring move smoothly.


HINT:

Make sure that the protruding part on the synchronizer ring is fitted into the groove of the clutch hub.



Hide 33352C 9.INSTALL SHAFT SNAP RING

a.
C277859C01
0.958,1.563 0.958,0.531 false 0.885,1.604 1.198,1.802 0.313,0.198 10 *a
*a Mark


Select a new shaft snap ring, using the table below, that makes the thrust clearance of the No. 3 transmission clutch hub less than 0.1 mm (0.00394 in.).

Standard shaft snap ring thickness:
Mark Thickness Mark Thickness
1 2.25 mm (0.0886 in.) 4 2.40 mm (0.0945 in.)
2 2.30 mm (0.0906 in.) 5 2.45 mm (0.0965 in.)
3 2.35 mm (0.0925 in.) 6 2.50 mm (0.0984 in.)



b.
C112462

Using a brass bar and hammer, tap the snap ring onto the No. 2 output shaft.


Hide 10.INSPECT 5TH DRIVEN GEAR THRUST CLEARANCE

Hide 11.INSPECT 5TH DRIVEN GEAR RADIAL CLEARANCE

Hide 33429B 12.INSTALL 6TH DRIVEN GEAR

a.
C116203

Install the spacer into the No. 2 output shaft.


b.
C116204

Coat the 2 pieces of the needle roller bearing with gear oil, and install them into the No. 2 output shaft.


c.
C116202

Coat the 6th gear synchronizer ring with gear oil, and install it into the No. 3 transmission clutch hub.


d.
C116555

Coat the 6th driven gear with gear oil, and install it into the No. 2 output shaft.


Hide 33322A 13.INSTALL REAR NO. 2 OUTPUT SHAFT BEARING

a.
C112458E01
0.159,0.263 0.469,0.586 0.31,0.323 10 SST 0.547,0.352 0.813,0.352 0.813,0.352 1.027,0.546 false

Using SST and press, press in the rear No. 2 output shaft bearing to the No. 2 output shaft.

SST
09710-04071  

NOTICE:

After installation, make sure that the gear and synchronizer ring move smoothly.



Hide 33322C 14.INSTALL NO. 2 OUTPUT SHAFT BEARING SNAP RING

a.
C277855C01
1.083,1.583 1.354,1.583 1.354,1.583 1.823,1.969 false 0.854,1.51 1.167,1.708 0.313,0.198 10 *a
*a Mark


Select a new No. 2 output shaft bearing snap ring, using the table below, that makes the thrust clearance of the 6th driven gear less than 0.1 mm (0.00394 in.).

Standard No. 2 output shaft bearing snap ring thickness:
Mark Thickness Mark Thickness
B 1.85 mm (0.0728 in.) 0 2.05 mm (0.0807 in.)
C 1.90 mm (0.0748 in.) 1 2.10 mm (0.0827 in.)
D 1.95 mm (0.0768 in.) 2 2.15 mm (0.0846 in.)
E 2.00 mm (0.0787 in.) - -



b.
C112395

Using a snap ring expander, install the No. 2 output shaft bearing snap ring onto the No. 2 output shaft.


Hide 15.INSPECT 6TH DRIVEN GEAR THRUST CLEARANCE

Hide 16.INSPECT 6TH DRIVEN GEAR RADIAL CLEARANCE

Hide 33322B 17.INSTALL FRONT NO. 2 OUTPUT SHAFT BEARING

a.
C112459E01
0.141,0.487 0.467,0.816 0.326,0.329 10 SST 0.941,1.027 0.54,0.588 0.54,0.588 0.998,0.588 false

Using SST and a press, press in the front No. 2 output shaft bearing into the No. 2 output shaft.

SST
09309-37010  
09506-30012  


Hide 33321N 18.INSTALL FRONT OUTPUT SHAFT BEARING

a.
C112466E01
0.152,1.133 0.483,1.491 0.331,0.358 10 SST 0.54,1.21 0.659,1.21 0.659,1.21 0.834,1.733 false

Using SST and press, press in the front output shaft bearing into the No. 1 output shaft.

SST
09309-14040  


Hide 33321Y 19.INSTALL FRONT OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C112426

Using a snap ring expander, install a new front output shaft bearing shaft snap ring into the No. 1 output shaft.


Hide 33335 20.INSTALL 1ST DRIVEN GEAR

a.
C112425

Coat the needle roller bearing with gear oil, and install it into the No. 1 output shaft.


b.
C277856

Coat the 1st driven gear with gear oil, and install it into the No. 1 output shaft.


Hide 33361 21.INSTALL NO. 1 TRANSMISSION CLUTCH HUB

a.
C116550

Apply of gear oil to the sleeve and hub.


b.

Install the hub sleeve to the clutch hub.


c.

Install the 3 shifting keys to the clutch hub.


d.

Install the 3 shifting key springs to the clutch hub.


e.

Place the 3 balls in the holes of the shifting keys, and install the hub sleeve while pushing in the balls.

NOTICE:

Take care to prevent the balls from scattering.



f.
C112467E01
2.133,1.577 2.423,1.757 0.29,0.181 10 SST 2.372,1.353 2.249,1.353 2.249,1.353 2.249,1.577 false

Coat the 3 pieces of the 1st driven gear synchronizer ring set with gear oil, and install them to the 1st driven gear.


g.

Using SST and a press, press in the No. 1 transmission hub sleeve to the No. 1 output shaft.

SST
09726-40010  

NOTICE:

After installation, make sure that the gear and synchronizer ring move smoothly.


HINT:

Make sure that the protruding part on the synchronizer ring is fitted into the groove of the clutch hub.



Hide 33332 22.INSTALL 2ND DRIVEN GEAR SYNCHRONIZER RING SET

a.
C112422

Coat the 3 pieces of the 2nd driven gear synchronizer ring set with gear oil, and install them to the No. 1 output shaft.


Hide 33365C 23.INSTALL SYNCHROMESH SHIFTING KEY BALL

C116562

a.

Using a magnet hand, install the synchromesh shifting key ball onto the No. 1 output shaft.


Hide 24.INSTALL NEEDLE ROLLER BEARING

a.
C112421

Coat the needle roller bearing with gear oil, and install it into the No. 1 output shaft.


Hide 33332 25.INSTALL 2ND DRIVEN GEAR

a.
C112420

Coat the 2nd driven gear with gear oil, and install it into the No. 1 output shaft.


Hide 33356A 26.INSTALL INNER 2ND DRIVEN GEAR BEARING RACE

a.
C112419

Align the groove of the inner 2nd driven gear bearing race with the synchromesh shifting key ball, and install it.


Hide 33321C 27.INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C112418

Using a snap ring expander, install the output shaft bearing shaft snap ring to the No. 1 output shaft.

HINT:

Do not damage the journal surface of the No. 1 output shaft.



Hide 33422B 28.INSTALL 4TH DRIVEN GEAR

a.
C112417

Install the spacer into the No. 1 output shaft.


b.
C112416

Coat the 2 pieces of the needle roller bearing with gear oil, and install them into the No. 1 output shaft.


c.
C116209

Coat the 4th driven gear with gear oil, and install it into the No. 1 output shaft.


Hide 33362 29.INSTALL NO. 2 TRANSMISSION CLUTCH HUB

a.
C116551

Apply of gear oil to the sleeve and hub.


b.

Install the hub sleeve to the clutch hub.


c.

Install the 3 shifting keys to the clutch hub.


d.

Install the 3 shifting key springs to the clutch hub.


e.

Place the 3 balls in the holes of the shifting keys, and install the hub sleeve while pushing in the balls.

NOTICE:

Take care to prevent the balls from scattering.



f.

Coat the 3 pieces of the 4th driven gear synchronizer ring set with gear oil, and install them into the 4th driven gear.


g.
C112468E01
0.691,0.288 1.023,0.634 0.332,0.346 10 SST 1.08,0.385 1.264,0.385 1.264,0.385 1.541,0.609 false

Using SST and a press, press in the No. 2 transmission hub sleeve to the No. 1 output shaft.

SST
09309-14010  

HINT:

Make sure that the protruding part on the synchronizer ring is fitted into the groove of the clutch hub.


NOTICE:

After installation, make sure that the gear and synchronizer ring move smoothly.



Hide 33352C 30.INSTALL SHAFT SNAP RING

a.
C277857C01
2.531,1.479 2.531,0.552 false 2.469,1.531 2.781,1.729 0.313,0.198 10 *a
*a Mark


Select a new shaft snap ring, using the table below, that makes the thrust clearance of the No. 2 transmission clutch hub less than 0.1 mm (0.00394 in.).

Standard shaft snap ring thickness:
Mark Thickness Mark Thickness
1 2.25 mm (0.0886 in.) 4 2.40 mm (0.0945 in.)
2 2.30 mm (0.0906 in.) 5 2.45 mm (0.0965 in.)
3 2.35 mm (0.0925 in.) 6 2.50 mm (0.0984 in.)



b.
C112469

Using a brass bar and hammer, tap the shaft snap ring into the No. 1 output shaft.


Hide 31.INSPECT 1ST DRIVEN GEAR THRUST CLEARANCE

Hide 32.INSPECT 1ST DRIVEN GEAR RADIAL CLEARANCE

Hide 33.INSPECT 2ND DRIVEN GEAR THRUST CLEARANCE

Hide 34.INSPECT 2ND DRIVEN GEAR RADIAL CLEARANCE

Hide 35.INSPECT 4TH DRIVEN GEAR THRUST CLEARANCE

Hide 36.INSPECT 4TH DRIVEN GEAR RADIAL CLEARANCE

Hide 33423A 37.INSTALL 3RD DRIVEN GEAR

a.
C112413

Coat the 3rd driven gear synchronizer ring set with gear oil, and install it into the No. 1 output shaft.


b.
C112412

Coat the needle roller bearing with gear oil, and install it into the No. 1 output shaft.


c.
C112411

Install the spacer into the No. 1 output shaft.


d.
C112410

Coat the 3rd driven gear with gear oil, and install it into the No. 1 output shaft.


Hide 33321N 38.INSTALL FRONT OUTPUT SHAFT BEARING

a.
C112465E02
0.877,0.084 1.186,0.31 0.309,0.226 10 SST 1.238,0.17 1.398,0.17 1.398,0.17 1.579,0.411 false

Using SST and press, press in the output shaft front bearing into the No. 1 output shaft.

SST
09308-14010  

HINT:

When pressing in the bearing, apply force to only the inner race. Do not apply force to the seal.


NOTICE:

After installation, make sure that the gear and synchronizer ring move smoothly.



Hide 33321B 39.INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C277861C01
2.979,1.26 2.979,0.719 false 2.885,1.323 3.198,1.521 0.313,0.198 10 *a
*a Mark


Select a new output shaft bearing shaft snap ring, using the table below, that makes the thrust clearance of the output shaft bearing less than 0.1 mm (0.00394 in.).

Standard output shaft bearing snap ring thickness:
Mark Thickness Mark Thickness
B 1.85 mm (0.0728 in.) 0 2.05 mm (0.0807 in.)
C 1.90 mm (0.0748 in.) 1 2.10 mm (0.0827 in.)
D 1.95 mm (0.0768 in.) 2 2.15 mm (0.0846 in.)
E 2.00 mm (0.0787 in.) - -



b.
C112408

Using a snap ring expander, install the output shaft bearing shaft snap ring onto the No. 1 output shaft.


Hide 40.INSPECT 3RD DRIVEN GEAR THRUST CLEARANCE

Hide 41.INSPECT 3RD DRIVEN GEAR RADIAL CLEARANCE