The 4WD ECU assembly is connected to the combination meter assembly via the CAN communication system.
for Segment Display Type:
If the 4WD ECU assembly stores any DTCs which are related to the dynamic torque control 4WD/AWD system , the 4WD/AWD warning light comes on in the combination meter assembly.
for Dot Display Type:
If the 4WD ECU assembly stores any DTCs which are related to the dynamic torque control AWD system , the master warning light comes on and the warning message is displayed on the multi-information display in the combination meter assembly.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check the condition of each related circuit connector before troubleshooting.
Check if CAN communication system DTCs are output.
for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM
for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM
Check if the dynamic torque control 4WD/AWD system DTC is output.
Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Neither CAN communication system DTC nor dynamic torque control 4WD/AWD system DTC is output | A |
| CAN communication DTC is output (for LHD) | B |
| CAN communication DTC is output (for RHD) | C |
| Dynamic torque control 4WD/AWD system DTC is output | D |
When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.
A
B
C
D
Check if the 4WD ECU assembly connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the battery voltage.
11 to 14 V
| Proceed to |
|---|
| OK |
| NG (for 2AR-FE) |
| NG (for 2AD-FHV) |
| NG (for 2AD-FTV) |
| NG (for 3ZR-FAE) |
| NG (for 3ZR-FE) |
OK
NG (for 2AR-FE)
NG (for 2AD-FHV)
NG (for 2AD-FTV)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)
| *a | Front view of wire harness connector
(to 4WD ECU Assembly) |
Disconnect the 4WD ECU assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G86-3 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to 4WD ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G86-4 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Warm up the engine.
Turn the ignition switch off.
Connect the GTS the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Four Wheel Drive / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| 4WD Warning Light | 4WD/AWD warning Light*1
AWD warning*2 |
OFF or ON | OFF: Warning light off*1
OFF: Warning off*2 ON: Warning light on*1 ON: Warning on*2 |
- |
*1: for Segment Display Type
*2: for Dot Display Type
| Tester Display |
|---|
| 4WD Warning Light |
Check the GTS diplay condition of the 4WD/AWD warning light.
| Proceed to |
|---|
| Display of the Data List remains OFF |
| Display of the Data List remains ON |
Display of the Data List remains OFF
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Display of the Data List remains ON