If a malfunction in the speed sensor signal circuit, deceleration sensor circuit*1 or acceleration sensor (airbag sensor assembly) circuit*2 occurs, the 4WD ECU assembly will output this DTC.
The airbag sensor assembly has a built-in acceleration sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1296/96 | ABS Malfunction | When one of the following conditions is met:
1.
Wheel speed sensor malfunction is received from the skid control ECU (brake actuator assembly) 2.
Deceleration sensor malfunction is received from skid control ECU (brake actuator assembly)*1 3.
Acceleration sensor (airbag sensor assembly) malfunction is received from skid control ECU (brake actuator assembly)*2 |
·
Brake control system (Speed sensor circuit) ·
Brake control system (Deceleration sensor circuit)*1 ·
Skid control ECU (Brake actuator assembly) ·
Acceleration sensor (airbag sensor assembly) circuit*2 ·
4WD ECU assembly |
*1: w/o VSC
*2: w/ VSC
Check the condition of each related circuit connector before troubleshooting.
Clear the DTC.
w/o VSC: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
w/ VSC: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON again.
Drive the vehicle, accelerate to a speed of 20 km/h (12 mph) or more, and check if the speed sensor DTC (brake control system DTC) is output.
w/o VSC: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
w/ VSC: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Brake control system DTC (speed sensor or deceleration sensor DTC) is not output (w/o VSC) | A |
| Brake control system DTC (speed sensor or acceleration sensor DTC) is not output (w/ VSC) | |
| Brake control system DTC (speed sensor or deceleration sensor DTC) is output (w/o VSC) | B |
| Brake control system DTC (speed sensor or acceleration sensor DTC) is output (w/ VSC) | C |
When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.
A
B
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Four Wheel Drive / Data List.
Read the value displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
| RR Wheel Speed |
| RL Wheel Speed |
The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
| Proceed to |
|---|
| OK |
| NG (w/o VSC) |
| NG (w/ VSC) |
OK
NG (w/o VSC)
NG (w/ VSC)
Enter the following menus: Chassis / Four Wheel Drive / Data List.
Read the value displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Forward and Rearward G | Forward and Rearward G | Min.: -25.10 m/s2
Max.: 24.90 m/s2 |
Approximately 0 +/-0.13 m/s2 while stationary | Changes in proportion with acceleration during acceleration/deceleration. |
| Tester Display |
|---|
| Forward and Rearward G |
w/o VSC:
The deceleration sensor output value is normal.
w/ VSC:
The acceleration sensor (airbag sensor assembly) output value is normal.
| Proceed to |
|---|
| OK |
| NG (w/o VSC) |
| NG (w/ VSC) |
OK
NG (w/o VSC)
NG (w/ VSC)