Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048750 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1468  SFR Solenoid Circuit  C1469  SFL Solenoid Circuit  C146A  SRR Solenoid Circuit  C146B  SRL Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1468 SFR Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more. Brake actuator assembly
C1469 SFL Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more. Brake actuator assembly
C146A SRR Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more. Brake actuator assembly
C146B SRL Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more. Brake actuator assembly

WIRING DIAGRAM

C284389E02
1.604,1.385 2.396,1.583 0.792,0.198 10 false ABS NO. 2 3.229,1.094 3.542,1.292 0.313,0.198 10 false 12 3.51,1.104 3.969,1.302 0.458,0.198 10 false +BS 4.563,0.75 5.521,0.958 0.958,0.208 10 false Solenoid Relay 5.927,1.583 6.542,1.781 0.615,0.198 10 false SFRH 5.958,2.135 6.573,2.333 0.615,0.198 10 false SFLH 5.979,2.646 6.594,2.844 0.615,0.198 10 false SRRH 6,3.135 6.615,3.333 0.615,0.198 10 false SRLH 5.958,3.635 6.573,3.833 0.615,0.198 10 false SFRR 5.958,4.135 6.573,4.333 0.615,0.198 10 false SFLR 5.958,4.635 6.573,4.833 0.615,0.198 10 false SRRR 5.969,5.135 6.583,5.333 0.615,0.198 10 false SRLR 3.323,4.969 3.479,5.167 0.156,0.198 10 false 1 3.563,5.083 4.177,5.281 0.615,0.198 10 false GND1 3.76,7.917 4.219,8.115 0.458,0.198 10 false A63 4.479,4.198 5.594,4.385 1.115,0.188 10 false Skid Control ECU 3.781,8.083 5.448,8.281 1.667,0.198 10 false Brake Actuator Assembly 0.177,1.198 1.01,1.396 0.833,0.198 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and CVT oil pressure calibration (for continuously variable transaxle).

K111: Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

K111F: Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the skid control ECU (brake actuator assembly).

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).


a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

d.

Check if the same DTC is recorded.

Result:
Proceed to
DTC is not output
DTC is output


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.





DTC is not output

DTC is output