Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR(w/o VSC) › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0049568 BRAKE ACTUATOR(w/o VSC) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(w/o VSC)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 4.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 5.DISCONNECT BRAKE LINE

a.
C274689

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator.


b.
C274690C01
0.813,0.417 0.667,0.292 0.667,0.292 0.5,0.292 false 1.219,0.604 0.656,0.938 0.656,0.938 0.458,0.938 false 1.771,0.677 1.938,0.177 1.938,0.177 2.479,0.177 false 2.198,0.813 2.5,0.563 2.5,0.563 2.75,0.563 false 0.333,1.646 0.219,1.792 0.219,1.792 0.219,1.896 false 1.313,1.99 1.177,2.26 1.177,2.26 1.177,2.406 false 0.292,0.208 0.51,0.406 0.219,0.198 10 false *1 2.823,0.49 3.042,0.688 0.219,0.198 10 false *2 2.531,0.094 2.75,0.292 0.219,0.198 10 false *3 0.219,0.854 0.406,1.052 0.188,0.198 10 false *4 1.104,2.469 1.323,2.667 0.219,0.198 10 true *6 0.146,1.958 0.354,2.156 0.208,0.198 10 true *5

Use tags or make a memo to identify the places to reconnect.

HINT:
·

*1: to front wheel cylinder RH

·

*2: to front wheel cylinder LH

·

*3: to rear wheel cylinder RH

·

*4: to rear wheel cylinder LH

·

*5: from front master cylinder

·

*6: from rear master cylinder




Hide 44510 6.REMOVE BRAKE ACTUATOR ASSEMBLY WITH BRACKET

a.

Release the lock lever and disconnect the brake actuator connector.

C274691C01
0.094,0.052 0.406,0.208 0.313,0.156 10 *A 3.521,0.063 3.833,0.219 0.313,0.156 10 *B
*A for 3ZR-FE *B for 2AR-FE


NOTICE:

Be careful not to allow brake fluid to enter the removed connector.



b.
C274692

Disconnect the brake tube clamp from the bracket.


c.
C274693

Remove the 3 nuts and actuator with bracket.

NOTICE:

Be careful not to damage the brake tubes.