Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1361  Short in ABS Motor Fail Safe Relay Circuit  C146C  Open in ABS Motor Relay Circuit  C146D  Short in ABS Motor Relay Circuit  


DESCRIPTION

The motor relay supplies power to the pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the pump motor.

If the voltage supplied to the motor relay (BM) is below the DTC's detection threshold due to low voltage from the battery or generator, the DTC may be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1361 Short in ABS Motor Fail Safe Relay Circuit Immediately after the ignition switch is turned to ON, the relay contact is closed for 4 seconds when the motor fail safe relay is OFF.
·

ABS NO. 1 fuse

·

Motor fail safe relay circuit

·

Brake actuator assembly (Motor fail safe relay)


C146C Open in ABS Motor Relay Circuit When either of the following is detected:
1.

All of the following conditions continue for 0.12 seconds or more.

·

The IG1 terminal voltage is between 9.5 and 17.4 V.

·

While initial check and ABS, BA, TRC/TRAC or VSC is operating.

·

Relay contact is open when the relay is ON.


2.

Both of the following conditions continue for 0.12 seconds.

·

The IG1 terminal voltage is 9.5 V or higher.

·

Relay contact remains open when the relay is ON.



·

ABS NO. 1 fuse

·

Motor relay circuit

·

Brake actuator assembly (Motor relay)


C146D Short in ABS Motor Relay Circuit When the motor relay is OFF, the motor relay remains closed for 4 seconds or more.
·

Motor relay circuit

·

Brake actuator assembly (Motor relay)



WIRING DIAGRAM

C283801E01
0.271,1.333 1.104,1.521 0.833,0.188 10 false from Battery 1.875,1.51 2.656,1.698 0.781,0.188 10 false ABS NO. 1 3.417,1.24 3.729,1.438 0.313,0.198 10 false 24 3.667,1.24 3.979,1.438 0.313,0.198 10 false BM 4.667,0.51 5.813,0.708 1.146,0.198 10 false Skid Control ECU 4.938,1.26 5.729,1.458 0.792,0.198 10 false Motor Relay 4.625,3.281 6.073,3.5 1.448,0.219 10 false Motor Fail Safe Relay 5.229,4.427 6.063,4.625 0.833,0.198 10 false Pump Motor 4.188,4.875 4.646,5.073 0.458,0.198 10 false A64 4.198,5.063 5.833,5.271 1.635,0.208 10 false Brake Actuator Assembly 3.406,2.854 3.719,3.052 0.313,0.198 10 false 13 3.656,2.854 4.271,3.052 0.615,0.198 10 false GND2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When C1241 is output together with C146C, C146D and/or C1361 inspect and repair the trouble areas indicated by C1241 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1241


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MOTOR RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


e.

According to the display on the GTS, perform the Active Test.


Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Motor Relay Motor relay Relay OFF/ON Operating sound of motor can be heard.
Vehicle condition: Vehicle stopped
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Motor Relay
50004 105 2
f.

Check the operating sound of the motor relay when operating it with the GTS.

Result:
Proceed to
The operating sound is not heard
The operating sound is heard




The operating sound is not heard

2.CHECK TERMINAL VOLTAGE (BM TERMINAL)

The operating sound is heard

4.RECONFIRM DTC
2.CHECK TERMINAL VOLTAGE (BM TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Check the connector case and terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.
C199357C54
1.583,0.104 1.979,0.365 0.396,0.26 2.604,1.813 2.458,1.313 false 1.667,0.156 2.021,0.354 0.354,0.198 10 false A64 2.51,1.844 2.823,2.042 0.313,0.198 10 false BM 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A64 skid control ECU (brake actuator assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64-24 (BM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BM CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.

Turn the ignition switch off.


b.
C199357C50
1.635,0.115 2.01,0.365 0.375,0.25 0.604,1.74 1.063,1.302 false 1.698,0.177 2.156,0.375 0.458,0.198 10 false A64 0.417,1.781 0.854,1.979 0.438,0.198 10 false GND2 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

4.RECONFIRM DTC
HINT:

These codes are stored when a problem is identified in the skid control ECU (brake actuator assembly). The motor relay is in the skid control ECU (brake actuator assembly). Therefore, motor relay inspections and motor relay unit inspections cannot be performed. Be sure to check if any DTCs are output before replacing the brake actuator assembly.


a.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.




DTC is not output

DTC is output