Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.04
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1417  High Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or generator circuit, etc.

The DTC is canceled when the IG1 terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1417 High Power Supply Voltage Malfunction The IG1 terminal voltage is 17.4 V or more for 0.8 seconds or more.
·

Charging system

·

Backup boost converter circuit (w/ Stop and Start System)

·

Internal power supply circuit of the skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.
C199357C49
1.625,0.083 2,0.333 0.375,0.25 2.219,1.854 2.292,1.406 false 0,0 0.313,0.156 0.313,0.156 10 false *a 1.688,0.125 2.146,0.323 0.458,0.198 10 false A64 2.135,1.875 2.427,2.073 0.292,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A64 skid control ECU (brake actuator assembly) connector.


c.

Start the engine.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64-34 (IG1) - Body ground Engine running 11 to 14 V



Result:
Proceed to
OK
NG (w/o Stop and Start System for 1AD-FTV)
NG (w/ Stop and Start System for 1AD-FTV)
NG (for 2AD-FHV)
NG (for 2AD-FTV)
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)



OK

2.RECONFIRM DTC

NG (w/o Stop and Start System for 1AD-FTV)

NG (w/ Stop and Start System for 1AD-FTV)

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

NG (for 2AD-FHV)

NG (for 2AD-FTV)

NG (for 2AR-FE)

NG (for 3ZR-FAE)

NG (for 3ZR-FE)

2.RECONFIRM DTC
a.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch off.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC C1417 is not output
DTC C1417 is output



DTC C1417 is not output

DTC C1417 is output