Home › Engine / Hybrid System › 2AD-FTV EMISSION CONTROL › MONOLITHIC CONVERTER(for DPF)
RM3090E _51 Engine / Hybrid System _008737 2AD-FTV EMISSION CONTROL _0048716 MONOLITHIC CONVERTER(for DPF) A

2AD-FTV EMISSION CONTROL  MONOLITHIC CONVERTER(for DPF)  INSTALLATION  


PROCEDURE

Hide 25587 1.INSTALL NO. 2 MANIFOLD CONVERTER INSULATOR

a.

Install the No. 2 manifold converter insulator with the 3 bolts.

Torque:
29 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 25734 2.INSTALL NO. 2 VACUUM PIPE

a.

Temporarily install the No. 2 vacuum pipe with the union nut and bolt.


b.

Tighten the bolt.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


c.

Using a 14 mm union nut wrench, tighten the union nut of the No. 2 vacuum pipe.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is click here combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 25733A 3.INSTALL NO. 1 VACUUM PIPE

a.

Temporarily install the No. 1 vacuum pipe with the union nut and bolt.


b.

Tighten the bolt.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


c.

Using a 17 mm union nut wrench, tighten the union nut of the No. 1 vacuum pipe.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is click here combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 25770A 6.INSTALL NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY

a.
A206303C01
1.688,1.24 2.167,1.354 2.167,1.354 2.354,1.354 true 2.375,1.24 2.688,1.396 0.313,0.156 10 *1 0.646,0.833 0.958,0.99 0.313,0.156 10 *a 1.292,1.521 1.75,1.719 0.458,0.198 10 30° 1.833,1.521 2.292,1.719 0.458,0.198 10 30°
*1 Paint Mark (Green)
*a LH Side
V100136

Front Side of The Vehicle


Install the No. 2 vacuum transmitting hose assembly to the No. 2 vacuum pipe, and slide the clamp to secure the hose.

HINT:

The direction of the hose clamp is indicated in the illustration.



Hide 25760A 7.INSTALL VACUUM TRANSMITTING HOSE ASSEMBLY

a.
A206304C01
2.344,1.323 2.219,1.323 2.219,1.323 1.646,1.219 false 2.375,1.208 2.688,1.354 0.313,0.146 10 *1 0.656,0.813 0.875,0.969 0.219,0.156 10 *a 1.24,1.552 1.615,1.729 0.375,0.177 10 30° 1.76,1.552 2.115,1.729 0.354,0.177 10 30°
*1 Paint Mark (Light Blue)
*a LH Side
V100136

Front Side of The Vehicle


Install the vacuum transmitting hose assembly to the No. 1 vacuum pipe, and slide the clamp to secure the hose.

HINT:

The direction of the hose clamp is indicated in the illustration.



Hide 25051 8.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.

Install a new gasket to the turbocharger sub-assembly.

HINT:
A197499C03
1.26,1.917 2.083,1.917 true 2.125,1.823 2.281,2.021 0.156,0.198 10 A
V100135

Top


Make sure that the part labeled A is facing downwards as shown in the illustration.



b.
A197484

Temporarily install the exhaust manifold converter sub-assembly with the 3 new nuts.


c.
A197482

Temporarily install the No. 2 exhaust manifold stay with the 2 bolts and nut.


d.
A197481

Temporarily install the No. 2 manifold stay with the 3 bolts.


e.
A197483

Temporarily install the manifold stay with the bolt and nut.


f.
A273038N02
1.573,0.417 1.729,0.615 0.156,0.198 10 1 1.323,1.896 1.479,2.094 0.156,0.198 10 2

Tighten the 2 bolts of the No. 2 exhaust manifold stay in the order shown in the illustration.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)


g.

Tighten the 3 nuts of the exhaust manifold converter sub-assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Tighten the nuts while pressing the exhaust manifold converter sub-assembly against the engine.



h.
A201849

Tighten the nut of the No. 2 exhaust manifold stay.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)


i.
A201845

Tighten the bolt of the No. 2 manifold stay shown in the illustration.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)

NOTICE:

Tighten the bolt while pressing the No. 2 manifold stay against the exhaust manifold converter sub-assembly and cylinder block sub-assembly.



j.
A201846

Tighten the 2 bolts of the No. 2 manifold stay shown in the illustration.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)


k.
A201850

Tighten the bolt of the manifold stay.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Tighten the bolt while pressing the manifold stay against the exhaust manifold converter sub-assembly and cylinder block sub-assembly.



l.
A201851

Tighten the nut of the manifold stay.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


m.

Connect the exhaust temperature sensor connector and No. 2 exhaust temperature sensor connector.


Hide 25586 9.INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR

a.

Install the No. 1 manifold converter insulator with the 5 bolts.

Torque:
29 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 11.PERFORM CATALYST RECORD OF DPF THERMAL DETERIORATION CLEAR FUNCTION