Check the radio automatic station search function by activating it.
| Proceed to |
|---|
| Automatic station search function does not stop |
| Automatic station search function stops on a station |
Automatic station search function does not stop
Automatic station search function stops on a station
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
Do not remove optional components without the permission of the customer.
| Proceed to |
|---|
| Optional components are not installed |
| Optional components are installed |
Optional components are not installed
Optional components are installed
Remove the roof antenna pole sub-assembly from the amplifier antenna assembly.
Turn the ignition switch ACC with the radio receiver assembly connector connected.
Turn the radio on and tune into AM mode.
Place a screwdriver, thin wire, or other metal object on the amplifier antenna threaded installation portion for the roof antenna pole sub-assembly and check that noise can be heard from the speakers.
| Proceed to |
|---|
| Noise does not occur |
| Noise occurs |
Noise does not occur
Noise occurs
Remove the antenna connector from the radio receiver assembly.
Turn the ignition switch ACC with the radio receiver assembly connector connected.
Turn the radio on and tune into AM mode.
Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.
| Proceed to |
|---|
| Noise can be heard from the speakers |
| Noise cannot be heard from the speakers |
Noise can be heard from the speakers
Noise cannot be heard from the speakers
Disconnect the RA radio receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (ANT+) - Body ground | Ignition switch ACC
Radio switch on and FM or AM selected |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD(for Roof Side)>REMOVAL
| Proceed to |
|---|
| Radio broadcasts can be received normally |
| Radio broadcasts cannot be received normally |
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally
Replace the No. 2 antenna cord sub-assembly and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD(for Roof Side)>REMOVAL
| Proceed to |
|---|
| Radio broadcasts can be received normally |
| Radio broadcasts cannot be received normally |
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally
Replace the No. 3 antenna cord sub-assembly and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD(for Roof Side)>REMOVAL
| Proceed to |
|---|
| Radio broadcasts can be received normally |
| Radio broadcasts cannot be received normally |
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally
Check that the roof antenna pole sub-assembly is securely installed.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL
| Proceed to |
|---|
| The roof antenna pole sub-assembly is installed properly |
| The roof antenna pole sub-assembly is not installed properly |
The roof antenna pole sub-assembly is installed properly
The roof antenna pole sub-assembly is not installed properly
Replace the roof antenna pole sub-assembly and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL
| Proceed to |
|---|
| Radio broadcasts can be received normally |
| Radio broadcasts cannot be received normally |
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally
Replace the antenna with holder assembly and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA HOLDER>REMOVAL
| Proceed to |
|---|
| Radio broadcasts can be received normally |
| Radio broadcasts cannot be received normally |
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally