Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › 2012.12–2015.10
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048747 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio receiver assembly.

WIRING DIAGRAM

E274383E01
5.24,3.01 6.844,3.25 1.604,0.24 10 false Radio Receiver Assembly 5.24,2.813 5.625,2.99 0.385,0.177 10 false G46 5.396,0.396 5.563,0.573 0.167,0.177 10 false 4 5.375,2.26 5.542,2.438 0.167,0.177 10 false 7 5.406,1.24 5.573,1.417 0.167,0.177 10 false 3 5.698,0.583 6.448,0.813 0.75,0.229 10 false +B1 5.708,1.354 6.458,1.583 0.75,0.229 10 false ACC1 5.708,2.458 6.458,2.688 0.75,0.229 10 false GND1 2.073,1.344 3.677,1.583 1.604,0.24 10 false from ACC Relay 3.927,1.552 4.323,1.771 0.396,0.219 10 false ACC 3.896,0.74 4.896,0.938 1,0.198 10 false RADIO 2.292,0.563 3.167,0.865 0.875,0.302 10 false from Battery 4.406,0.438 4.583,0.625 0.177,0.188 10 false *1 4.417,1.219 4.594,1.406 0.177,0.188 10 false *1 4.406,0.063 4.583,0.25 0.177,0.188 10 false *2 4.417,0.885 4.594,1.073 0.177,0.188 10 false *2 1.115,0.24 1.49,0.469 0.375,0.229 10 false BO1 1.104,1 1.479,1.229 0.375,0.229 10 false ACO 1.573,0.896 1.74,1.073 0.167,0.177 10 false 3 1.563,0.125 1.729,0.302 0.167,0.177 10 false 2 0.542,1.365 0.927,1.542 0.385,0.177 10 false G87 0.552,1.573 1.604,2.052 1.052,0.479 10 false Engine Stop and Start ECU*2 0.177,2.969 2.542,3.25 2.365,0.281 10 false *1: w/o Stop and Start System 0.198,3.344 2.563,3.625 2.365,0.281 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Proceed to
w/o Stop and Start System
w/ Stop and Start System



w/o Stop and Start System

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

w/ Stop and Start System

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - ENGINE STOP AND START ECU AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E259248C09
1.51,0.396 1.896,0.594 0.385,0.198 2.5,1.406 2.135,1.104 true 1.271,1.646 1.594,1.365 true 2.229,0.604 1.927,1 true 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.573,0.417 1.917,0.625 0.344,0.208 10 false G46 2.563,1.333 3.115,1.552 0.552,0.219 10 false +B1 1.063,1.667 1.5,1.865 0.438,0.198 10 false GND1 2.302,0.51 2.854,0.729 0.552,0.219 10 false ACC1
*a Front view of wire harness connector
(to Radio Receiver Assembly)


Disconnect the radio receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G46-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G46-4 (+B1) - Body ground Always 11 to 14 V
G46-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - ENGINE STOP AND START ECU AND BODY GROUND)
a.

Disconnect the G46 radio receiver assembly connector.


b.

Disconnect the G87 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G46-4 (+B1) - G87-2 (BOI) Always Below 1 Ω
G46-3 (ACC1) - G87-3 (ACO) Always Below 1 Ω
G46-7 (GND1) - Body ground Always Below 1 Ω
G46-4 (+B1) - Body ground Always 10 kΩ or higher
G46-3 (ACC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENGINE STOP AND START ECU
a.
E259248C04
1.51,0.396 1.896,0.594 0.385,0.198 2.375,0.729 2.146,1.021 false 1.938,1 2.323,0.396 true 0.146,0.115 0.458,0.271 0.313,0.156 10 *a 1.573,0.417 1.917,0.625 0.344,0.208 10 G46 2.438,0.646 2.99,0.865 0.552,0.219 10 +B 2.396,0.302 3.01,0.5 0.615,0.198 10 ACC1
*a Front view of wire harness connector
(to Radio Receiver Assembly)


Disconnect the radio receiver assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G46-4 (+B1) - Body ground Always 10.5 to 14 V
G46-3 (ACC1) - Body ground Ignition switch ACC 10.5 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG