Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) Y

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:

*: Use the GTS.


PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

HINT:
·

Whether the vehicle battery is discharged can be checked simply by operating the horn.

·

After recharging the battery, initialize the integrated current value* and drive the vehicle until stop and start control operation is permitted (approximately 15 to 40 minutes).

*: Disconnect the cables from the battery, wait for 30 seconds or more and then reconnect the cables.




b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC AND FREEZE FRAME DATA*
4.CHECK DTC AND FREEZE FRAME DATA*
a.

Check for DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227

b.

Check for freeze frame data.

HINT:

Record or print DTCs and freeze frame data if necessary.



c.

Clear the DTCs and freeze frame data.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Recheck for DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227
HINT:

If any DTCs for the CAN communication system are output, troubleshoot those DTCs first.


Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

5.PROBLEM SYMPTOMS TABLE

DTC is output

5.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>PROBLEM SYMPTOMS TABLE

Result:
Proceed to
Fault is not listed in problem symptoms table
Fault is listed in problem symptoms table




Fault is not listed in problem symptoms table

6.OVERALL ANALYSIS AND TROUBLESHOOTING*

Fault is listed in problem symptoms table

7.REPAIR OR REPLACE
6.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

7.REPAIR OR REPLACE
7.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

8.CONFIRMATION TEST
8.CONFIRMATION TEST
a.

Warm up the engine.


b.

Turn the air conditioning system off.


c.

Drive the vehicle for 15 to 40 minutes.


d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal. Check if the engine is stopped by the stop and start control.

HINT:

If the engine is not stopped by stop and start control, air fuel ratio learning and idle speed learning are necessary. Allow the engine to idle for 3 minutes and check that the engine speed is within 50 rpm of the target idle speed.



e.

Depress the clutch pedal and that the engine restarts.


Result:
Proceed to
NEXT



NEXT

END