Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.12–2015.10
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E269549E02
1.802,1.875 3.229,2.083 1.427,0.208 10 false from IG1 NO.1 Relay 2.063,1.354 3.125,1.552 1.063,0.198 10 false from ACC Relay 2.292,0.563 3.115,0.771 0.823,0.208 10 false from Battery 3.719,2.052 4.719,2.271 1,0.219 10 false ECU-IG NO.2 3.969,1.531 4.365,1.74 0.396,0.208 10 false ACC 3.917,0.74 4.458,0.948 0.542,0.208 10 false RADIO 5.208,0.583 5.708,0.771 0.5,0.188 10 false G141 5.219,1.354 5.656,1.563 0.438,0.208 10 false G141 5.188,1.885 5.813,2.094 0.625,0.208 10 false G143 5.198,2.448 5.688,2.656 0.49,0.208 10 false G141 5.656,0.583 5.99,0.792 0.333,0.208 10 false +B1 5.656,1.354 6.031,1.542 0.375,0.188 10 false ACC1 5.667,1.885 5.896,2.083 0.229,0.198 10 false IG 5.656,2.448 6.125,2.646 0.469,0.198 10 false GND1 5.448,2.854 6.667,3.219 1.219,0.365 10 false Radio and Display Receiver Assembly 5.354,0.365 5.521,0.552 0.167,0.188 10 false 4 5.344,1.125 5.51,1.313 0.167,0.188 10 false 3 5.323,1.688 5.49,1.875 0.167,0.188 10 false 1 5.333,2.271 5.5,2.458 0.167,0.188 10 false 7 0.167,2.99 2.26,3.177 2.094,0.188 10 false *1: w/o Stop and Start System 0.167,3.354 2.052,3.625 1.885,0.271 10 false *2: w/ Stop and Start System 1.135,0.229 1.479,0.417 0.344,0.188 10 false BO1 0.552,1.531 1.615,1.958 1.063,0.427 10 false Engine Stop and Start ECU*2 4.448,0.448 4.76,0.646 0.313,0.198 10 false *1 4.448,0.094 4.76,0.292 0.313,0.198 10 false *2 4.479,1.229 4.792,1.427 0.313,0.198 10 false *1 4.458,0.885 4.771,1.083 0.313,0.198 10 false *2 1.135,1.01 1.594,1.208 0.458,0.198 10 false ACO 1.552,0.125 1.708,0.323 0.156,0.198 10 false 2 1.583,0.854 1.74,1.052 0.156,0.198 10 false 3 0.531,1.344 0.99,1.542 0.458,0.198 10 false G87

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Proceed to
w/o Stop and Start System
w/ Stop and Start System



w/o Stop and Start System

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

w/ Stop and Start System

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ENGINE STOP AND START ECU)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E256516C03
1.531,1.688 1.938,1.906 0.406,0.219 1.458,0.26 1.865,0.479 0.406,0.219 1.604,1.198 1.156,1.448 false 2.438,1.177 2.188,0.927 false 2.354,0.646 1.979,0.865 false 0.938,2.531 0.667,2.531 false 1.5,0.281 1.896,0.469 0.396,0.188 10 G141 1.583,1.719 1.99,1.896 0.406,0.177 10 G143 0.865,1.479 1.396,1.688 0.531,0.208 10 GND1 2.5,1.135 2.948,1.354 0.448,0.219 10 +B1 2.396,0.573 2.927,0.76 0.531,0.188 10 ACC1 0.448,2.438 0.865,2.667 0.417,0.229 10 IG 0.052,0.052 0.365,0.25 0.313,0.198 10 *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G141-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Stop and Start System:
Tester Connection Condition Specified Condition
G141-4 (+B1) - G141-7 (GND1) Always 11 to 14 V
G141-3 (ACC1) - G141-7 (GND1) Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
G143-1 (IG) - G141-7 (GND1) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Standard Voltage:
w/ Stop and Start System:
Tester Connection Condition Specified Condition
G141-4 (+B1) - G141-7 (GND1) Always 10.5 to 14 V
G141-3 (ACC1) - G141-7 (GND1) Ignition switch ACC 10.5 to 14 V
Ignition switch off Below 1 V
G143-1 (IG) - G141-7 (GND1) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ENGINE STOP AND START ECU)
a.

Disconnect the G141 radio and display receiver assembly connector.


b.

Disconnect the G87 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G141-4 (+B1) - G87-2 (BO1) Always Below 1 Ω
G141-3 (ACC1) - G87-3 (ACO) Always Below 1 Ω
G141-4 (+B1) - Body ground Always 10 kΩ or higher
G141-3 (ACC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENGINE STOP AND START ECU
a.
E259248C05
1.51,0.396 1.896,0.594 0.385,0.198 2.375,0.729 2.146,1.021 false 1.938,1 2.323,0.396 true 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.542,0.417 1.927,0.625 0.385,0.208 10 false G141 2.438,0.646 2.99,0.865 0.552,0.219 10 false +B1 2.396,0.302 3.01,0.5 0.615,0.198 10 false ACC1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Reconnect the G87 engine stop and start ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G141-4 (+B1) - Body ground Always 10.5 to 14 V
G141-3 (ACC1) - Body ground Ignition switch ACC 10.5 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E256516C04
1.531,1.688 1.938,1.906 0.406,0.219 1.458,0.26 1.865,0.479 0.406,0.219 1.604,1.198 1.156,1.448 false 0.938,2.531 0.667,2.531 false 1.5,0.281 1.896,0.469 0.396,0.188 10 G141 1.583,1.719 1.99,1.896 0.406,0.177 10 G143 0.865,1.479 1.396,1.688 0.531,0.208 10 GND1 0.448,2.438 0.865,2.667 0.417,0.229 10 IG 0.052,0.052 0.365,0.25 0.313,0.198 10 *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G141-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G143-1 (IG) - G141-7 (GND1) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR