Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › 2012.12–2015.10
RM3090E _59 Vehicle Exterior _008430 LIGHTING (EXT) _0047056 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM D

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  INITIALIZATION  


HEIGHT CONTROL SENSOR SIGNAL INITIALIZATION (WHEN NOT USING GTS)


NOTICE:
·

Initialize the height control sensor signal after the vehicle height changes due to replacement of the suspension or after performing such operations as removal and reinstallation or replacement of the rear height control sensor.

·

Initialization is also necessary when the headlight leveling ECU is replaced.

·

Adjust the headlight aim after initializing the headlight leveling ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for HID Headlight)>ADJUSTMENT

·

When a malfunction is detected in the automatic headlight beam level control system, the height control sensor signal initialization is impossible. Perform troubleshooting before initialization.




1. PREPARE VEHICLE FOR INITIALIZATION


a.

Unload the trunk and vehicle, and make sure that the spare tire, tools and jack are in their original positions.


b.

Check that there are no occupants in the vehicle.


c.

Turn off the headlights.


d.

Stop the vehicle on a level surface and keep the vehicle height unchanged.



2. CHECK WARNING LIGHT


a.
E270844C01
0.25,0.188 0.563,0.385 0.313,0.198 10 *a
*a Headlight Beam Level Control System Warning Light


Turn the ignition switch to ON and check the headlight beam level control system warning light.

OK:
Condition Specified Condition
The headlight leveling ECU is replaced with a new one. Warning light continuously blinks 6 times at 2 Hz.
Removal and reinstallation of the headlight leveling ECU, replacement of the rear height control sensor, removal and reinstallation of the rear height control sensor, replacement of the suspension, etc. Warning light comes on for approximately 3 seconds, and then turns off (bulb check function).


HINT:

If the warning light does not come on when turning the ignition switch to ON, perform inspections and repairs according to "Problem Symptoms Table".

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




3. INITIALIZATION


SST
09843-18040  

a.
C166029C56
1.604,0.896 1.906,0.333 false 2.375,1.021 2.844,1.083 false 2.885,0.99 3.24,1.167 0.354,0.177 10 LVL 1.938,0.229 2.302,0.406 0.365,0.177 10 CG 0.125,0.073 0.344,0.25 0.219,0.177 10 *a
*a Front view of DLC3


Connect terminals 4 (CG) and 8 (LVL) of the DLC3 using SST.


b.
E270694N01
2.354,0.542 2.51,0.74 0.156,0.198 10 E 2.573,1.365 2.729,1.563 0.156,0.198 10 D 2.5,2.167 2.656,2.365 0.156,0.198 10 C 2.24,2.781 2.396,2.979 0.156,0.198 10 B 1.75,3.229 1.906,3.427 0.156,0.198 10 A

Turn the low beam headlights on and off using the light control switch within 20 seconds after connecting the terminals.

HINT:

The number of times the low beam headlights need to be turned on and off is determined by the present fuel level as shown below.


Fuel Level Number of Times to Turn Low Beam Headlights on and off
Fuel level is within range A. 1
Fuel level is within range B. 2
Fuel level is within range C. 3
Fuel level is within range D. 4
Fuel level is within range E. 5

NOTICE:
·

Turn the low beam headlights on and off at approximately 3-second intervals.

·

Be sure to operate the headlight dimmer switch from the outside of the vehicle.




c.

Check the warning light.

OK:
Condition Specified Condition
The headlight leveling ECU is replaced with a new one. Blinks 6 times at 2 Hz → Blinks 3 times at 2 Hz, and then turns off.
Removal and reinstallation of the headlight leveling ECU, replacement of the rear height control sensor, removal and reinstallation of the rear height control sensor, replacement of the suspension, etc. Off → Blinks 3 times at 2 Hz, and then turns off


HINT:
·

If the calculated vehicle height is not within the acceptable range, the rear height control sensor initialization will end as an abnormal termination, and the warning light will blink 6 times at 2 Hz continuously. Disconnect SST from the DLC3 and turn the ignition switch off. Then restart from "Check Warning Light".

·

If initialization cannot be finished normally, check the LVL terminal circuit (Click here Vehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>LVL Terminal Circuit), or perform inspections and repairs according to "Problem Symptoms Table" (Click here Vehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).





HEIGHT CONTROL SENSOR SIGNAL INITIALIZATION (WHEN USING GTS)


NOTICE:
·

Initialize the height control sensor signal after the vehicle height changes due to replacement of the suspension or after performing such operations as removal and reinstallation or replacement of the rear height control sensor.

·

Initialization is also necessary when the headlight leveling ECU is replaced.

·

Adjust the headlight aim after initializing the headlight leveling ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for HID Headlight)>ADJUSTMENT

·

When a malfunction is detected in the automatic headlight beam level control system, the height control sensor signal initialization is impossible. Perform troubleshooting before initialization.




1. PREPARE VEHICLE FOR INITIALIZATION


a.

Unload the trunk and vehicle, and make sure that the spare tire, tools and jack are in their original positions.


b.

Check that there are no occupants in the vehicle.


c.

Turn off the headlights.


d.

Stop the vehicle on a level surface and keep the vehicle height unchanged.



2. CHECK WARNING LIGHT


a.
E270844C01
0.25,0.188 0.563,0.385 0.313,0.198 10 *a
*a Headlight Beam Level Control System Warning Light


Turn the ignition switch to ON and check the headlight beam level control system warning light.

OK:
Condition Specified Condition
The headlight leveling ECU is replaced with a new one. Warning light continuously blinks 6 times at 2 Hz.
Removal and reinstallation of the headlight leveling ECU, replacement of the rear height control sensor, removal and reinstallation of the rear height control sensor, replacement of the suspension, etc. Warning light comes on for approximately 3 seconds, and then turns off (bulb check function).


HINT:

If the warning light does not come on when turning the ignition switch to ON, perform inspections and repairs according to "Problem Symptoms Table".

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




3. INITIALIZATION


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Utility / Height Sensor Initialization / Next.


e.

Check what is displayed on the screen of the GTS and press "Next".


f.
E270694N01
2.354,0.542 2.51,0.74 0.156,0.198 10 E 2.573,1.365 2.729,1.563 0.156,0.198 10 D 2.5,2.167 2.656,2.365 0.156,0.198 10 C 2.24,2.781 2.396,2.979 0.156,0.198 10 B 1.75,3.229 1.906,3.427 0.156,0.198 10 A

Check the fuel level of the fuel receiver gauge in the combination meter. The appropriate position ID is determined by the present fuel level.

Fuel Level Position ID
A EMPTY
B 1/4 to over EMPTY
C 1/2 to over 1/4
D 3/4 to over 1/2
E FULL to over 3/4


g.

Enter the determined position ID into the GTS and press "Next".

HINT:

If the position ID has not been entered, "Next" cannot be pressed.



h.

Check the warning light.

OK:
Condition Specified Condition
The headlight leveling ECU is replaced with a new one. Blinks 6 times at 2 Hz → Blinks 3 times at 2 Hz, and then turns off.
Removal and reinstallation of the headlight leveling ECU, replacement of the rear height control sensor subassembly, removal and reinstallation of the rear height control sensor subassembly, replacement of the suspension, etc. Off → Blinks 3 times at 2 Hz, and then turns off.



i.

Press "Exit".

HINT:
·

If the calculated vehicle height is not within the acceptable range, the rear height control sensor initialization will end as an abnormal termination, and the warning light will blink 6 times at 2 Hz continuously. Disconnect SST from the DLC3 and turn the ignition switch off. Then restart from "Check Warning Light".

·

If initialization cannot be finished normally, check the LVL terminal circuit (Click here Vehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>LVL Terminal Circuit), or perform inspections and repairs according to "Problem Symptoms Table" (Click here Vehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).