Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › VALVE BODY ASSEMBLY › 2012.12–2014.10
RM3090E _52 Drivetrain _008752 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0049171 VALVE BODY ASSEMBLY A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  REMOVAL  


PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER (for Full Cover Type)

Hide 51444C 2.REMOVE REAR ENGINE UNDER COVER LH

Hide 3.DRAIN AUTOMATIC TRANSAXLE FLUID

a.

Remove the refill plug and gasket from the automatic transaxle assembly.


b.
C205876

Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket from the automatic transaxle assembly.


c.

Using a 6 mm socket hexagon wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle assembly and drain the automatic transaxle fluid.


d.
C162883C01
0.833,2.625 1.792,2.625 false 0.885,3.49 1.781,3.49 false 0.667,3.167 0.292,4.094 0.292,4.094 1.177,4.094 true 1.833,2.531 2.042,2.688 0.208,0.156 10 *1 1.25,4.01 1.427,4.188 0.177,0.177 10 *a 1.833,3.406 2.031,3.635 0.198,0.229 10 *2
*1 No. 1 Transmission Oil Filler Tube
*2 Hexagon Socket Wrench
*a Overflow Plug Hole


Using a 6 mm socket hexagon wrench, install the No. 1 transmission oil filler tube to the automatic transaxle assembly.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)


e.

Using a 6 mm socket hexagon wrench, install a new gasket and the overflow plug to the automatic transaxle assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


f.

Temporarily install the gasket and the refill plug to the automatic transaxle assembly.


Hide 51218A 4.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.
C206484

Remove the 4 bolts and front suspension member reinforcement LH.


Hide 35106D 5.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C274831

Remove the 19 bolts and automatic transaxle oil pan sub-assembly from the transaxle case.

NOTICE:

Some fluid will remain in the automatic transaxle oil pan sub-assembly. Remove all the bolts, and carefully remove the automatic transaxle oil pan sub-assembly.



b.

Remove the automatic transaxle oil pan gasket from the automatic transaxle oil pan sub-assembly.


c.

Remove the 2 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.


d.

Examine particles in the automatic transaxle oil pan sub-assembly.

i.

Collect any steel chips with the removed transmission oil cleaner magnets. Look carefully at the chips and particles in the automatic transaxle oil pan sub-assembly and on the transmission oil cleaner magnets to see the type of wear which might be found in the automatic transaxle assembly.

Result:
Steel (magnetic):

Bearing, gear and plate wear

Brass (non-magnetic):

Bushing wear




Hide 35330 6.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.
C201702

Remove the 2 bolts and valve body oil strainer assembly from the transmission valve body assembly.


b.
C201703

Remove the O-ring from the valve body oil strainer assembly.


Hide 35410 7.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C201704

Remove the 11 bolts and transmission valve body assembly from the transaxle case.

NOTICE:

When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and the transaxle case to interfere with each other.



Hide 35145C 8.REMOVE TRANSAXLE CASE GASKET

a.
C201316

Remove the 2 transaxle case gaskets from the transaxle case.


Hide 35418 9.REMOVE MANUAL VALVE

a.
C201705

Remove the manual valve from the transmission valve body assembly.