As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.
for Manual Transaxle:
When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.
1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
2.DISCHARGE FUEL SYSTEM PRESSURE
w/ Canister Pump Module
Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/ Canister Pump Module)>PRECAUTION
w/o Canister Pump Module
Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/o Canister Pump Module)>PRECAUTION
3. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
5.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
51441
6.REMOVE NO. 1 ENGINE UNDER COVER
| *A | for Half Cover Type |
| *B | for Full Cover Type |
for Half Cover Type:
Remove the 6 screws, 5 clips and No. 1 engine under cover.
for Full Cover Type:
Remove the 2 screws, 4 bolts, 8 clips and No. 1 engine under cover.
51443
7.REMOVE REAR ENGINE UNDER COVER RH
Remove the 3 clips and rear engine under cover RH.
51444C
8.REMOVE REAR ENGINE UNDER COVER LH
| *A | for Half Cover Type |
| *B | for Full Cover Type |
for Half Cover Type:
Remove the 3 clips and rear engine under cover LH.
for Full Cover Type:
Remove the 2 clips and rear engine under cover LH.
50819
9.REMOVE FRONT FLOOR COVER (w/ Canister Pump Module)
10.DRAIN ENGINE COOLANT
11.DRAIN ENGINE OIL
12.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)
for 4WD/AWD
Click hereDrivetrain>EB63F MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSAXLE OIL>REPLACEMENT
13.DRAIN TRANSFER OIL (for 4WD/AWD)
14.DRAIN AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)
for 4WD/AWD
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>REMOVAL
12601B
15.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
74404A
16.REMOVE BATTERY CLAMP SUB-ASSEMBLY
28899
17.REMOVE BATTERY INSULATOR
28800
18.REMOVE BATTERY
74431
19.REMOVE BATTERY TRAY
74411B
20.REMOVE FRONT BATTERY BRACKET
74414B
21.REMOVE BATTERY BRACKET REINFORCEMENT
17705
22.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
23.REMOVE AIR CLEANER CASE
89661
24.REMOVE ECM
16470
25.DISCONNECT RADIATOR RESERVOIR ASSEMBLY
16361A
26.REMOVE FAN AND GENERATOR V BELT
27020
27.REMOVE GENERATOR ASSEMBLY
16572D
28.DISCONNECT NO. 2 RADIATOR HOSE
16581B
29.REMOVE RADIATOR HOSE HOSE CLAMP
16057
30.DISCONNECT RADIATOR HOSE SUB-ASSEMBLY
88703
31.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY
88704
32.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
33493A
33.REMOVE TRANSMISSION OIL COOLER (for Automatic Transaxle)
for 2WD
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>OIL COOLER>REMOVAL
for 4WD/AWD
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>OIL COOLER>REMOVAL
23901
34.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the No. 1 fuel pipe clamp.
Disconnect the fuel tube connector.
Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/o Canister Pump Module)>PRECAUTION
35.DISCONNECT WIRE HARNESS AND HOSE
Remove the terminal cap.
Remove the nut, and disconnect the clamp and starter wire harness.
Remove the bolt. Then disconnect the 2 clamps and wire harness.
Remove the nut from the engine room No. 1 relay block.
Disconnect the 2 connectors, detach the 2 claws from the engine room No. 1 relay block and disconnect the wire harness.
Remove the bolt and disconnect the wire harness.
Slide the clip and disconnect the vacuum hose from the No. 1 hose to hose tube.
for Manual Transaxle:
Detach the heater hose from the clamp.
Slide the clip and disconnect the heater hose from the cylinder head sub-assembly.
Slide the clip and disconnect the heater hose from the No. 1 water by-pass pipe.
for Automatic Transaxle:
Slide the clip and disconnect the heater hose from the cylinder head sub-assembly.
Slide the clip and disconnect the heater hose from the No. 1 water by-pass pipe.
33820B
36.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
Remove the 4 clips and disconnect the 2 transmission control cables.
33820B
37.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)
Remove the nut and disconnect the transmission control cable from the control shaft lever.
Remove the clip and disconnect the transmission control cable from the control cable bracket.
45259A
38.REMOVE COLUMN HOLE COVER SILENCER SHEET
45260
39.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45025D
40.DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
43502H
41.REMOVE FRONT AXLE SHAFT NUT LH
43501H
42.REMOVE FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
43.DISCONNECT FRONT SPEED SENSOR LH
44.DISCONNECT FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
48810
45.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH
48820B
46.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
45047
47.DISCONNECT TIE ROD END SUB-ASSEMBLY LH
45046
48.DISCONNECT TIE ROD END SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
48069
49.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
50.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
43420
51.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
for 4WD/AWD
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 4WD/AWD)>REMOVAL
43420G
52.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH
for 4WD/AWD
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 4WD/AWD)>REMOVAL
43410
53.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
for 4WD/AWD
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY(for 4WD/AWD)>REMOVAL
43457
54.REMOVE DRIVE SHAFT BEARING BRACKET
Remove the 3 bolts and bracket.
11361J
55.REMOVE FLYWHEEL HOUSING UNDER COVER
Remove the flywheel housing under cover.
31418
56.DISCONNECT CLUTCH HOSE (for Manual Transaxle)
Using a 10 mm union nut wrench, disconnect the clutch hose from the accumulator to flexible hose tube.
Remove the clip and disconnect the clutch hose.
17402
57.REMOVE FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY
17401
58.REMOVE FRONT EXHAUST PIPE SUB-ASSEMBLY
32101A
59.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for Automatic Transaxle)
for 4WD/AWD
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL
37100
60.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)
51218A
61.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH
Remove the 4 bolts and front suspension member reinforcement LH.
51217A
62.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH
Remove the 4 bolts and front suspension member reinforcement RH.
63.INSTALL ENGINE HANGER
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install 2 engine hangers with 2 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-36020 |
| No. 2 Engine Hanger | 12282-36021 |
| Bolt | 91552-81025
91552-81040 |
64.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Remove the 6 bolts and front crossmember sub-assembly.
Remove the through bolt, nut and front engine mounting insulator.
While holding the nut in place, loosen the through bolt.
Set an engine lifter underneath the engine.
Place the engine on wooden blocks or equivalent so that the engine is level.
Remove the bolt and 2 nuts and disconnect the engine mounting insulator sub-assembly RH.
Remove the bolt and nut and disconnect the engine mounting insulator LH.
Remove the 6 bolts and front suspension member rear brace RH and front suspension member rear brace LH.
Remove the 2 bolts and front suspension crossmember sub-assembly.
Operate the engine lifter and slowly remove the engine from the vehicle.
Make sure that the engine is clear of all wiring and hoses.
While lowering the engine from the vehicle, do not allow it to contact the vehicle.
Attach an engine sling device and hang the engine with a chain block.
Remove the through bolt and front suspension crossmember sub-assembly from the engine with transaxle.
Do not damage any engine or transaxle components.
Raise the engine with transaxle assembly while keeping it level.
28100
65.REMOVE STARTER ASSEMBLY
36100
66.REMOVE TRANSFER ASSEMBLY (for 4WD/AWD)
30300
67.REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)
for 4WD/AWD
Click hereDrivetrain>EB63F MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSAXLE ASSEMBLY>REMOVAL
30500
68.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)
for 4WD/AWD
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL
69.FIX ENGINE ASSEMBLY
Using wooden blocks or plate lift attachments, set the engine on a flat surface.
Place wooden blocks or plate lift attachments so that the engine is level.
Never install attachments to the oil pan of the engine assembly or transmission as doing so may deform the oil pan.
Perform this step while supporting the engine assembly using a sling device and chain block.
31210
70.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)
31250
71.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)
31400
72.REMOVE CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY (for Manual Transaxle)
13405
73.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)
32101
74.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)
82121
75.REMOVE ENGINE WIRE
Remove the engine wire from the engine.
76.INSTALL ENGINE TO ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Install the engine to an engine stand with the bolts.
Remove the 2 bolts and 2 engine hangers.
12371A
77.REMOVE REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
Remove the 2 bolts, 2 nuts and rear engine mounting insulator.
12305
78.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Remove the bolt and radiator reservoir bracket.
Remove the 3 bolts and engine mounting insulator sub-assembly RH.
12341
79.REMOVE ENGINE MOUNTING SPACER
Perform this procedure only when replacement of the engine mounting spacer is necessary.
Remove the 2 bolts and engine mounting spacer.
12372A
80.REMOVE ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Remove the bolt and wire harness clamp bracket.
Remove the 4 bolts and engine mounting insulator LH.