Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › OIL COOLER
RM3090E _52 Drivetrain _008752 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0049173 OIL COOLER A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL COOLER  INSTALLATION  


PROCEDURE

Hide 33493A 1.INSTALL TRANSMISSION OIL COOLER

a.

Install the transmission oil cooler to the front engine mounting bracket with the 2 bolts.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


b.
C280477C01
1.354,0.135 1.698,0.135 1.698,0.135 1.813,0.26 true 1.865,0.396 2.271,0.396 true 0.646,1.313 1.188,1.313 1.188,1.313 1.292,1.542 true 0.781,1.313 1.031,1.917 true 1.188,0.052 1.5,0.208 0.313,0.156 10 *a 2.302,0.313 2.615,0.469 0.313,0.156 10 *b 0.49,1.219 0.802,1.375 0.313,0.156 10 *c 2.208,0.063 2.521,0.219 0.313,0.156 10 A 2.115,0.625 2.427,0.781 0.313,0.156 10 B 1.615,1.25 1.927,1.406 0.313,0.156 10 C 1.438,1.708 1.75,1.865 0.313,0.156 10 D
*a Red Paint Mark
*b White Paint Mark
*c Yellow Paint Mark


Install the No. 8 water by-pass hose and No. 9 water by-pass hose, and slide the clips to secure it.

NOTICE:
·

Make sure the paint marks are aligned as shown in the illustration.

·

Make sure that the claws marked A in the illustration are facing toward the top of the vehicle.

·

Make sure that the claws marked B in the illustration are facing toward the LH of the vehicle.

·

Make sure that the claws marked C in the illustration are facing toward the front end of the vehicle.

·

Make sure that the claws marked D in the illustration are facing toward the underside of the vehicle.




c.

Attach the 3 clamp to the No. 8 water by-pass hose and No. 9 water by-pass hose.


d.
C280478C01
1.073,0.469 1.01,0.198 1.01,0.198 0.75,0.198 true 1.635,0.458 1.729,0.135 1.729,0.135 2.115,0.135 true 1.99,1.885 2.125,1.635 2.125,1.635 2.365,1.635 true 1.708,1.573 1.583,1.385 1.583,1.385 1.354,1.385 true 2.156,0.052 2.469,0.208 0.313,0.156 10 *a 0.583,0.125 0.896,0.281 0.313,0.156 10 *b 1.198,1.302 1.51,1.458 0.313,0.156 10 *c 2.406,1.552 2.719,1.708 0.313,0.156 10 *a 1.25,1.677 1.417,1.833 0.167,0.156 10 A 2.365,1.969 2.531,2.125 0.167,0.156 10 A
*a Pink Paint Mark
*b Yellow Paint Mark
*c White Paint Mark


Install the oil cooler inlet hose and oil cooler outlet hose, and slide the clips to secure it.

NOTICE:
·

Make sure the paint marks are aligned as shown in the illustration.

·

Make sure that the claws marked A in the illustration are facing toward the front end of the vehicle.

·

Position the claws of the clips so that they do not interfere with other parts unless otherwise specified.




Hide 74414B 2.INSTALL BATTERY BRACKET REINFORCEMENT

Hide 74411B 3.INSTALL FRONT BATTERY BRACKET

Hide 74431 4.INSTALL BATTERY TRAY

Hide 28800 5.INSTALL BATTERY

Hide 28899 6.INSTALL BATTERY INSULATOR

Hide 74404A 7.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 8.CONNECT CABLE TO POSITIVE BATTERY TERMINAL

Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).