Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › 2012.12–2014.10
RM3090E _52 Drivetrain _008752 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0049182 DIFFERENTIAL CASE A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL DIFFERENTIAL SIDE GEAR

a.
C278985C01
2.594,0.448 2.927,0.448 false 0.76,0.396 1.094,0.396 false 0.771,0.729 1.104,0.729 false 1.438,1.625 1.771,1.625 false 1.448,1.927 1.781,1.927 false 1.948,0.51 1.813,0.51 1.813,0.51 1.76,0.781 false 0.792,1.583 0.74,1.854 0.74,1.854 0.604,1.854 false 1.188,1 1.521,1 false 1.021,1.385 1.354,1.385 false 3,0.365 3.313,0.521 0.313,0.156 10 false *1 0.583,0.646 0.896,0.802 0.313,0.156 10 false *2 0.573,0.302 0.885,0.458 0.313,0.156 10 false *3 1.406,1.313 1.719,1.469 0.313,0.156 10 false *4 2,0.438 2.313,0.594 0.313,0.156 10 false *5 1.833,1.844 2.146,2 0.313,0.156 10 false *3 1.823,1.542 2.135,1.698 0.313,0.156 10 false *2 0.438,1.771 0.75,1.927 0.313,0.156 10 false *5 1.01,0.927 1.323,1.083 0.313,0.156 10 false *4
*1 Differential Case
*2 Differential Side Gear
*3 No. 1 Front Differential Side Gear Thrust Washer
*4 Front Differential Pinion
*5 Front Differential Pinion Thrust Washer


Coat the 2 differential side gears, 2 No. 1 front differential side gear thrust washers, 2 front differential pinions and 2 front differential pinion thrust washers with ATF and install them to the differential case.


Hide 41342F 2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C138706

Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.


Hide 3.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

Hide 41342A 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C138707

Using a 5 mm pin punch and hammer, install the front differential pinion shaft straight pin.

NOTICE:

Align the holes, and install the front differential pinion shaft straight pin.



b.
C138711

Using a chisel and hammer, stake the differential case.

NOTICE:

Stake the differential case after adjusting the backlash.



Hide 41221 5.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the front differential ring gear to more than 110°C (230°F).



b.
C317727C04
1.167,1.469 0.427,0.99 0.427,0.99 1.229,1.406 true 0.24,0.833 0.677,1.25 0.438,0.417 10 false *a
*a Matchmark


Clean the contact surface of the differential case.


c.

Align the matchmarks, set the front differential ring gear to the front differential case.


d.
C317728

Install the 12 bolts.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:
·

Tighten the bolts after the front differential ring gear has cooled down sufficiently.

·

Tighten the bolts evenly in a diagonal pattern using several steps.