Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › 2012.12–2015.10
RM3090E _59 Vehicle Exterior _008793 SLIDING ROOF / CONVERTIBLE _0049191 SLIDING ROOF SYSTEM J

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  Sliding Roof does not Move by Operating Sliding Roof Control Switch  


DESCRIPTION

The sliding roof drive gear sub-assembly (sliding roof ECU) receives slide and tilt signals when the sliding roof control switch is operated and drives its built-in motor.

WIRING DIAGRAM

B344650E01
3.49,0.552 4.104,0.75 0.615,0.198 10 false LIN2 5.625,0.563 6.24,0.76 0.615,0.198 10 false MPX1 5.635,1.552 6.25,1.75 0.615,0.198 10 false B 5.646,1.969 6.26,2.167 0.615,0.198 10 false IG 5.406,1.448 5.573,1.646 0.167,0.198 10 false 8 5.406,1.865 5.573,2.063 0.167,0.198 10 false 1 3.958,1.708 4.573,1.906 0.615,0.198 10 false S/ROOF 1.104,1.531 2.021,1.74 0.917,0.208 10 false from Battery 0.594,1.948 2,2.167 1.406,0.219 10 false from IG1 NO.1 Relay 3.802,2.146 4.719,2.344 0.917,0.198 10 false ECU-IG NO.1 5.635,2.385 6.25,2.583 0.615,0.198 10 false E 5.344,2.271 5.573,2.479 0.229,0.208 10 false 12 5.635,2.948 6.25,3.146 0.615,0.198 10 false OPN 3.615,3.313 4.229,3.51 0.615,0.198 10 false CLS 5.635,3.698 6.25,3.896 0.615,0.198 10 false DWN 5.635,3.958 6.25,4.156 0.615,0.198 10 false UP 3.698,4.063 4.313,4.26 0.615,0.198 10 false UP 3.458,3.813 4.073,4.01 0.615,0.198 10 false DOWN 5.635,3.208 6.25,3.406 0.615,0.198 10 false CLS 3.594,3.063 4.208,3.26 0.615,0.198 10 false OPN 5.427,2.865 5.656,3.073 0.229,0.208 10 false 7 5.427,3.094 5.656,3.302 0.229,0.208 10 false 5 5.438,3.615 5.667,3.823 0.229,0.208 10 false 6 5.438,3.854 5.667,4.063 0.229,0.208 10 false 4 3.979,2.865 4.208,3.073 0.229,0.208 10 false 3 3.99,3.104 4.219,3.313 0.229,0.208 10 false 2 3.99,3.615 4.219,3.823 0.229,0.208 10 false 4 4,3.854 4.229,4.063 0.229,0.208 10 false 5 2.073,2.979 2.24,3.177 0.167,0.198 10 false 1 2.26,3.208 2.875,3.406 0.615,0.198 10 false GND3 5.469,4.406 6.083,4.604 0.615,0.198 10 false Q8 5.469,4.615 6.677,5.25 1.208,0.635 10 false Sliding Roof Drive Gear Sub-assembly (Sliding Roof ECU) 2.26,4.375 2.875,4.573 0.615,0.198 10 false Q7 2.26,4.583 4.094,4.979 1.833,0.396 10 false Map Light Assembly (Sliding Roof Control Switch) 0.646,5.438 2.479,5.677 1.833,0.24 10 false : LIN Communication Line 1.677,1 4.729,1.229 3.052,0.229 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the sliding roof drive gear sub-assembly (sliding roof ECU) is removed and reinstalled or replaced, it requires initialization.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

The sliding roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

Click here

·

When a sliding roof drive gear sub-assembly (sliding roof ECU) DTC is output, first perform troubleshooting for the sliding roof drive gear sub-assembly (sliding roof ECU) DTC.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Sliding Roof / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch OPEN switch signal ON or OFF ON: OPEN switch pressed
OFF: OPEN switch not pressed
-
Close Switch CLOSE switch signal ON or OFF ON: CLOSE switch pressed
OFF: CLOSE switch not pressed
-
Up Switch UP switch signal ON or OFF ON: UP switch pressed
OFF: UP switch not pressed
-
Down Switch DOWN switch signal ON or OFF ON: DOWN switch pressed
OFF: DOWN switch not pressed
-
Body Electrical > Sliding Roof > Data List
Tester Display
Open Switch
Close Switch
Up Switch
Down Switch
50003 147 1,4,7,10
OK:

The GTS display changes according to switch operation as shown in the table.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY AND BODY GROUND)

NG

3.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF CONTROL SWITCH)
2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY AND BODY GROUND)
a.
B295816C08
1.542,0.313 1.927,0.604 0.385,0.292 2.563,1.563 2.458,1.563 2.458,1.563 2.135,1.396 true 0.875,1.563 0.969,1.563 0.969,1.563 1.292,1.396 true 0.854,1.042 0.948,1.042 0.948,1.042 1.281,1.135 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 1.635,0.365 1.917,0.552 0.281,0.188 10 false Q8 0.677,1.479 0.958,1.667 0.281,0.188 10 false B 2.635,1.49 2.917,1.677 0.281,0.188 10 false E 0.635,0.958 0.917,1.146 0.281,0.188 10 false IG
*a Front view of wire harness connector
(to Sliding Roof Drive Gear Sub-assembly [Sliding Roof ECU])


Disconnect the sliding roof drive gear sub-assembly (sliding roof ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Q8-8 (B) - Body ground Always 11 to 14 V
Q8-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Q8-1 (IG) - Body ground Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q8-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF CONTROL SWITCH)
a.
B338690N02
1.417,1.146 0.844,0.833 0.844,0.833 0.49,0.833 true 1.615,1.135 1.042,0.521 1.042,0.521 0.781,0.521 true 1.823,1.135 2.083,0.5 2.083,0.5 2.354,0.5 true 2.01,1.135 2.396,0.719 2.396,0.719 2.667,0.719 true 2.271,1.219 2.448,1.344 2.448,1.344 2.719,1.344 true 0.271,0.76 0.5,0.958 0.229,0.198 10 UP 0.302,0.448 0.781,0.615 0.479,0.167 10 DOWN 2.406,0.417 2.885,0.583 0.479,0.167 10 OPN 2.719,0.646 3.198,0.813 0.479,0.167 10 CLS 2.76,1.26 3.24,1.427 0.479,0.167 10 GND3

Remove the map light assembly (sliding roof control switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (UP) - 1 (GND3) UP switch is pressed Below 1 Ω
5 (UP) - 1 (GND3) UP switch is not pressed 10 kΩ or higher
4 (DOWN) - 1 (GND3) DOWN switch is pressed Below 1 Ω
4 (DOWN) - 1 (GND3) DOWN switch is not pressed 10 kΩ or higher
3 (OPN) - 1 (GND3) OPEN switch is pressed Below 1 Ω
3 (OPN) - 1 (GND3) OPEN switch is not pressed 10 kΩ or higher
2 (CLS) - 1 (GND3) CLOSE switch is pressed Below 1 Ω
2 (CLS) - 1 (GND3) CLOSE switch is not pressed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF CONTROL SWITCH AND BODY GROUND)

NG

REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF CONTROL SWITCH)

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF CONTROL SWITCH AND BODY GROUND)
a.

Disconnect the Q7 map light assembly (sliding roof control switch) connector.


b.

Disconnect the Q8 sliding roof drive gear sub-assembly (sliding roof ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q8-5 (CLS) - Q7-2 (CLS) Always Below 1 Ω
Q8-5 (CLS) - Body ground Always 10 kΩ or higher
Q8-7 (OPN) - Q7-3 (OPN) Always Below 1 Ω
Q8-7 (OPN) - Body ground Always 10 kΩ or higher
Q8-6 (DWN) - Q7-4 (DOWN) Always Below 1 Ω
Q8-6 (DWN) - Body ground Always 10 kΩ or higher
Q8-4 (UP) - Q7-5 (UP) Always Below 1 Ω
Q8-4 (UP) - Body ground Always 10 kΩ or higher
Q7-1 (GND3) - Body ground Always Below 1 Ω
Q8-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR