When the sliding roof drive gear sub-assembly (sliding roof ECU) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored.
When the sliding roof drive gear sub-assembly (sliding roof ECU) detects a gear position malfunction and the sliding roof operation is stopped, DTC B2344 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2341 | Sensor (Motor) Failure | Sensor (motor) failure (When the sliding roof ECU enters fail-safe mode due to a problem with the motor) | ·
Sliding roof drive gear sub-assembly (Sliding roof ECU) ·
Map light assembly (Sliding roof control switch) ·
Harness or connector |
| B2344 | Position Failure | Position failure (When the sliding roof ECU enters fail-safe mode due to a problem with the gear position) | ·
Sliding roof drive gear sub-assembly (Sliding roof ECU) ·
Map light assembly (Sliding roof control switch) ·
Harness or connector |
When the sliding roof drive gear sub-assembly (sliding roof ECU) is removed and reinstalled or replaced, it requires initialization.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
The sliding roof system uses the CAN and LIN communication systems. First, confirm that there are no malfunctions in the CAN and LIN communication systems. Refer to the How to Proceed with Troubleshooting procedure.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check the sliding roof auto operation.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>OPERATION CHECK
| Proceed to |
|---|
| Auto operation operates normally |
| Auto operation does not operate normally |
Auto operation operates normally
Auto operation does not operate normally
Clear the DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B2341 or B2344 is not output |
| DTC B2341 or B2344 is output |
DTC B2341 or B2344 is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC B2341 or B2344 is output
Check that the sliding roof drive gear sub-assembly (sliding roof ECU) can be initialized.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
Sliding roof drive gear sub-assembly (sliding roof ECU) can be initialized.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B2341 or B2344 is not output |
| DTC B2341 or B2344 is output |
DTC B2341 or B2344 is not output
DTC B2341 or B2344 is output
Disconnect the Q7 map light assembly (sliding roof control switch) connector.
Disconnect the Q8 sliding roof drive gear sub-assembly (sliding roof ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q8-5 (CLS) - Q7-2 (CLS) | Always | Below 1 Ω |
| Q8-5 (CLS) - Body ground | Always | 10 kΩ or higher |
| Q8-7 (OPN) - Q7-3 (OPN) | Always | Below 1 Ω |
| Q8-7 (OPN) - Body ground | Always | 10 kΩ or higher |
| Q8-6 (DWN) - Q7-4 (DOWN) | Always | Below 1 Ω |
| Q8-6 (DWN) - Body ground | Always | 10 kΩ or higher |
| Q8-4 (UP) - Q7-5 (UP) | Always | Below 1 Ω |
| Q8-4 (UP) - Body ground | Always | 10 kΩ or higher |
| Q7-1 (GND3) - Body ground | Always | Below 1 Ω |
| Q8-12 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly (sliding roof control switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (UP) - 1 (GND3) | UP switch is pressed | Below 1 Ω |
| 5 (UP) - 1 (GND3) | UP switch is not pressed | 10 kΩ or higher |
| 4 (DOWN) - 1 (GND3) | DOWN switch is pressed | Below 1 Ω |
| 4 (DOWN) - 1 (GND3) | DOWN switch is not pressed | 10 kΩ or higher |
| 3 (OPN) - 1 (GND3) | OPEN switch is pressed | Below 1 Ω |
| 3 (OPN) - 1 (GND3) | OPEN switch is not pressed | 10 kΩ or higher |
| 2 (CLS) - 1 (GND3) | CLOSE switch is pressed | Below 1 Ω |
| 2 (CLS) - 1 (GND3) | CLOSE switch is not pressed | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG