Home › Power Source / Network › 2AD-FHV BATTERY / CHARGING › CHARGING SYSTEM
RM3090E _57 Power Source / Network _008778 2AD-FHV BATTERY / CHARGING _0049277 CHARGING SYSTEM C

2AD-FHV BATTERY / CHARGING  CHARGING SYSTEM  P0516  Battery Temperature Sensor Circuit Low  P0517  Battery Temperature Sensor Circuit High  


DESCRIPTION

The battery thermometer sensor detects the battery temperature.

The battery current sensor has a built-in thermistor with a resistance that changes in response to changes in the battery temperature.

When the battery temperature is low the thermistor resistance increases, and when the temperature is high the resistance decreases.

The battery thermometer sensor is connected to the ECM.

A power supply voltage of 5 V is supplied to the battery temperature sensor from terminal THB of the ECM via resistor R.

As resistor R and the battery thermometer sensor are connected in series, when the resistance changes in response to changes in the battery temperature, the electric potential at terminal THB also changes.

Based on this signal, the ECM protects the battery by reducing the charge current when the battery temperature is high.

A110648
0.5,1.948 1.469,1.969 1.469,1.969 1.469,2.427 false 0.323,2.365 0.479,2.563 0.156,0.198 10 0 0.313,2.104 0.469,2.302 0.156,0.198 10 1 0.323,1.875 0.479,2.073 0.156,0.198 10 2 0.323,1.615 0.479,1.813 0.156,0.198 10 3 0.323,1.375 0.479,1.573 0.156,0.198 10 4 0.323,1.135 0.479,1.333 0.156,0.198 10 5 0.313,0.896 0.469,1.094 0.156,0.198 10 6 0.813,2.5 1.083,2.667 0.271,0.167 10 10 1.198,2.5 1.469,2.667 0.271,0.167 10 20 1.583,2.5 1.854,2.667 0.271,0.167 10 30 1.979,2.5 2.25,2.667 0.271,0.167 10 40 2.375,2.5 2.646,2.667 0.271,0.167 10 50 2.76,2.5 3.031,2.667 0.271,0.167 10 60 0.771,2.667 1.083,2.917 0.313,0.25 10 (50) 1.156,2.667 1.5,2.917 0.344,0.25 10 (68) 1.542,2.667 1.833,2.917 0.292,0.25 10 (86) 1.885,2.667 2.219,2.917 0.333,0.25 10 (104) 2.281,2.667 2.635,2.917 0.354,0.25 10 (122) 2.667,2.667 3,2.917 0.333,0.25 10 (140) 2.531,2.865 3.021,3.198 0.49,0.333 10 °C (°F)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0516 Battery Temperature Sensor Circuit Low Battery thermometer sensor output value is abnormally low for 0.5 seconds or more with the ignition switch ON
(1 trip detection logic)
·

Battery current sensor assembly (battery thermometer sensor)

·

ECM

·

Wire harness or connector


Does not come on DTC stored
P0517 Battery Temperature Sensor Circuit High Battery thermometer sensor output value is abnormally high for 0.5 seconds or more with the ignition switch ON
(1 trip detection logic)
·

Battery current sensor assembly (battery thermometer sensor)

·

ECM

·

Wire harness or connector


Does not come on DTC stored

WIRING DIAGRAM

A299199
0.906,1.24 2.792,1.698 1.885,0.458 10 false Battery Current Sensor 0.885,2.042 2.229,2.448 1.344,0.406 10 false Battery Thermometer Sensor 2.271,0.49 2.729,0.688 0.458,0.198 10 false VC5 2.406,0.917 2.719,1.115 0.313,0.198 10 false IB 2.385,2.458 2.698,2.656 0.313,0.198 10 false E2 0.427,2.969 0.885,3.167 0.458,0.198 10 false B72 2.302,1.677 2.615,1.875 0.313,0.198 10 false THB 2.688,0.479 2.844,0.677 0.156,0.198 10 false 2 2.698,0.917 2.854,1.167 0.156,0.25 10 false 3 2.708,1.667 2.865,1.917 0.156,0.25 10 false 1 2.729,2.448 2.885,2.698 0.156,0.25 10 false 4 0.76,2.979 3.24,3.365 2.479,0.385 10 false Battery Current Sensor Assembly 5.104,0.479 5.406,0.667 0.302,0.188 10 false 75 5.052,0.917 5.385,1.083 0.333,0.167 10 false 116 5.052,1.667 5.385,1.833 0.333,0.167 10 false 115 5.115,2.458 5.448,2.625 0.333,0.167 10 false 77 5.365,0.594 5.844,0.823 0.479,0.229 10 false VCIB 5.396,1.042 5.708,1.24 0.313,0.198 10 false IB 5.365,1.833 5.823,2.031 0.458,0.198 10 false THB 5.365,2.583 5.823,2.781 0.458,0.198 10 false EIB 5.354,2.927 5.813,3.125 0.458,0.198 10 false B76 5.677,2.927 6.135,3.125 0.458,0.198 10 false ECM

PROCEDURE

1.INSPECT BATTERY CURRENT SENSOR ASSEMBLY
a.

Inspect the battery current sensor assembly.

Click herePower Source / Network>2AD-FHV BATTERY / CHARGING>BATTERY CURRENT SENSOR>INSPECTION

Result:
Result
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR ASSEMBLY - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR ASSEMBLY - ECM)
a.

Disconnect the B76 ECM connector.


b.

Disconnect the B72 battery current sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
B76-77 (EIB) - B72-4 (E2) Always Below 1 Ω
B76-75 (VCIB) - B72-2 (VC5) Always Below 1 Ω
B76-115 (THB) - B72-1 (THB) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
B76-77 (EIB) or B72-4 (E2) - Body ground Always 10 kΩ or higher
B76-75 (VCIB) or B72-2 (VC5) - Body ground Always 10 kΩ or higher
B76-115 (THB) or B72-1 (THB) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR