If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Power source mode does not change to on (IG) but does change to on (ACC) | Power Source Control:
·
Power Supply Condition ·
IG1 Relay Monitor(Inside) ·
IG2 Relay Monitor(Inside) ·
IG1 Relay Monitor(Outside) ·
IG2 Relay Monitor(Outside) ·
IG1 Circuit ·
IG2 Circuit |
- |
Refer to DTC B2271.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>B2271
When using the GTS with the engine switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.
The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting.
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Start Function) precaution.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After completing repairs, confirm that the problem does not occur.
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Disconnect the G82 connectors from the certification ECU (smart key ECU assembly).
Remove the IG2 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-9 (IG2D) - 1 | Always | Below 1 Ω |
| 2 - Body ground | ||
| G82-9 (IG2D) or 1 - Body ground | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG2 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G84 connector from the certification ECU (smart key ECU assembly).
Disconnect the 3C and 3D connectors from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G84-6 (IG1D) - 3C-43 | Always | Below 1 Ω |
| 3D-9 - Body ground | ||
| G84-6 (IG1D) or 3C-43 - Body ground | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-1 - 3C-27 | Battery voltage not applied to terminals 3D-9 and 3C-43 | 10 kΩ or higher |
| Battery voltage applied to terminals 3D-9 and 3C-43 | Below 1 Ω | |
| 3A-1 - 3C-1 | Battery voltage not applied to terminals 3D-9 and 3C-43 | 10 kΩ or higher |
| Battery voltage applied to terminals 3D-9 and 3C-43 | Below 1 Ω | |
| 3A-1 - 3C-3 | Battery voltage not applied to terminals 3D-9 and 3C-43 | 10 kΩ or higher |
| Battery voltage applied to terminals 3D-9 and 3C-43 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G82-9 (IG2D) - Body ground | Engine switch on (ACC) → Engine switch on (IG) | 1 V or less → 9 V or higher |
| G84-6 (IG1D) - Body ground | Engine switch on (ACC) → Engine switch on (IG) | 1 V or less → 9 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG