Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function)
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0049280 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (ACC)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (ACC) but does change to on (IG)
Power Source Control
·

Power Supply Condition

·

ACC Relay Monitor


-


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Start Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G84 connector from the certification ECU (smart key ECU assembly).


b.

Disconnect the 3C and 3D connectors from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-4 (ACCD) - 3C-45 Always Below 1 Ω
3D-9 - Body ground
G84-4 (ACCD) or 3C-45 - Body ground 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

C278638C01
3.365,2.229 3.854,2.5 0.49,0.271 1.531,0.385 2.021,0.656 0.49,0.271 4.542,0.406 5.031,0.677 0.49,0.271 0.365,0.198 0.677,0.354 0.313,0.156 10 false *a 1.698,0.438 2.021,0.604 0.323,0.167 10 false 3C 4.708,0.469 5.031,0.635 0.323,0.167 10 false 3D 3.5,2.292 3.823,2.458 0.323,0.167 10 false 3A
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-1 - 3D-51 Battery voltage not applied to terminals 3C-45 and 3D-9 10 kΩ or higher
Battery voltage applied to terminals 3C-45 and 3D-9 Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B268626C13
1.333,0.188 1.792,0.469 0.458,0.281 1.125,1.01 0.813,0.51 false 1.417,0.25 2.031,0.448 0.615,0.198 10 false G84 0.406,0.406 1.021,0.604 0.615,0.198 10 false ACCD 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the G84 certification ECU (smart key ECU assembly) connector


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G84-4 (ACCD) - Body ground Engine switch off → Engine switch on (ACC) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)